Bosch GST 700 (0.601.2A7.021) - Инструкция по эксплуатации - Страница 13

 English | 

13

Bosch Power Tools

1 609 92A 3BD | (16.5.17)

Noise/Vibration Information

Sound emission values determined according to 
EN 60745-2-11.

Typically the A-weighted noise levels of the product are: 
Sound pressure level 90 dB(A); Sound power level 
101 dB(A). Uncertainty K = 3 dB.

Wear hearing protection!

Vibration total values a

h

 (triax vector sum) and uncertainty K 

determined according to EN 60745-2-11: 
Cutting wood: a

h

= 4.0 m/s

2

, K = 1.5 m/s

2

,

Cutting sheet metal: a

h

= 4.0 m/s

2

, K = 1.5 m/s

2

.

The vibration level given in this information sheet has been 
measured in accordance with a standardised test given in 
EN 60745 and may be used to compare one tool with another. 
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main 
applications of the tool. However if the tool is used for different 
applications, with different accessories or insertion tools or is 
poorly maintained, the vibration emission may differ. This may 
significantly increase the exposure level over the total working 
period.
An estimation of the level of exposure to vibration should also 
take into account the times when the tool is switched off or 
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from 
the effects of vibration such as: maintain the tool and the acces-
sories, keep the hands warm, organisation of work patterns.

Assembly

Replacing/Inserting the Saw Blade



When mounting the saw blade, wear protective gloves. 

Danger of injury when touching the saw blade.

Selecting a Saw Blade

An overview of recommended saw blades can be found at the 
end of these instructions. Use only T-shank saw blades. The saw 
blade should not be longer than required for the intended cut.

Use a thin saw blade for narrow curve cuts.

Inserting/Replacing the Saw Blade (see figure A)

Splinter Guard (see figure B)

The splinter guard 

14

 (accessory) can prevent fraying of the 

surface while sawing wood. The splinter guard can be used 
only at a cutting angle of 0 °.

Press the splinter guard 

14

 from the bottom into the base 

plate 

6

.

Dust/Chip Extraction



Dust from materials such as lead-containing coatings, 
some wood types, minerals and metal can be harmful to 
one’s health. Touching or breathing-in the dust can cause 
allergic reactions and/or lead to respiratory infections of 
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment 
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the 
materials to be worked.



Prevent dust accumulation at the workplace. 

Dust can 

easily ignite.

Operation

Operating Modes

Orbital Action Settings

The four orbital action settings allow for optimal adaptation of 
cutting speed, cutting capacity and cutting pattern to the 
material being sawed.

The orbital action can be adjusted with the adjusting lever 

7

, 

even during operation.

The optimal orbital action setting for the respective applica-
tion can be determined through practical testing. The follow-
ing recommendations apply:
– Select a lower orbital action setting (or switch it off) for a 

finer and cleaner cutting edge.

– For thin materials such as sheet metal, switch the orbital 

action off.

– For hard materials such as steel, work with low orbital action.
– For soft materials and when sawing in the direction of the 

grain, work with maximum orbital action.

Adjusting the Cutting Angle (see figure C)

The base plate 

6

 can be swivelled by 45° to the left or right for 

mitre cuts.

Loosen the screw 

15

 with the Allen key 

4

 and slide the base 

plate 

6

 slightly towards the saw blade 

10

.

For adjustment of precise mitre angles, the base plate has 
adjustment notches on the left and right at 0 ° and 45 °. Swivel 
the base plate 

6

 to the desired position according to the scale 

16

. Other mitre angles can be adjusted using a protractor.

Afterwards, push the base plate 

6

 to the stop toward the 

mains cable.

Tighten the screw 

15

 again.

The splinter guard 

14

 can not be inserted for mitre cuts.



Insert the saw blade 

10

 until it latches in the SDS saw 

blade receptacle 

8

.

While inserting the saw blade, pay attention that the back 
of the saw blade is positioned in the groove of the guide 
roller 

9

.



Check the tight seating of the saw blade. 

A loose saw 

blade can fall out and lead to injuries.




Slide the cover of the saw blade holder 

8

 upwards in the 

direction of the arrow and remove the saw blade 

10

.

O

No orbital action

I

Small orbital action

II

Medium orbital action

III

Large orbital action

OBJ_BUCH-3039-002.book  Page 13  Tuesday, May 16, 2017  9:52 AM