Skil 0750 - Инструкция по эксплуатации - Страница 10

10

APPLICATION ADVICE

•  For trimming a hedge at a uniform height level

-  fasten a piece of string along the length of the hedge 

at the desired height

-  trim the hedge just above this string

•  Recommended cutting/trimming times (Western Europe)

-  trim hedges with deciduous leaves in June and 

October

-  trim evergreen hedges in April and August

-  trim conifers and other fast-growing shrubs every 6 

weeks from May until October

MAINTeNANCe / serVICe

•  This tool is not intended for professional use

•  Keep tool, charger and cutting blades clean

!  unplug charger from power source before 

cleaning

!  always remove the battery before cleaning

-  clean the tool with a damp cloth (do not use cleaning 

agents or solvents)

-  clean ventilation slots J 

2

 regularly with a brush or 

compressed air

-  after use, always carefully clean and lightly lubricate 

the cutting blades

!  wear gloves when handling or cleaning the 

cutting blades

•  Regularly check the condition of the cutting blades and 

the tightness of the blade bolts

•  Regularly check for worn or damaged components and 

have them repaired/replaced when necessary

•  Sharpening the cutting blades

!  remove battery from tool

-  remove cutting blades from tool before sharpening

-  sharpen the cutting blades with a small and smooth 

file, in case a solid object damaged them

-  we advise you, however, to have the blades sharpened 

by a specialist

-  lubricate the cutting blades after sharpening

•  Storage 

¡

-  store the tool 

indoors

 in a dry and locked-up place, 

out of reach of children

-  securely mount storage rail K on the wall with 4 screws 

(

not supplied

) and horizontally leveled

-  use blade guards L 

2

 when storing the tool

-  lubricate the cutting blades before storing the tool

•  If the tool/charger should fail despite the care taken in 

manufacturing and testing procedures, repair should be 

carried out by an after-sales service centre for SKIL 

power tools

-  send the tool or charger 

undismantled

 together with 

proof of purchase to your dealer or the nearest SKIL 

service station (addresses as well as the service 

diagram of the tool are listed on www.skil.com)

-  in case of a defective charger send 

both charger and 

battery

 to your dealer or the SKIL service station

TroUBlesHooTING

•  The following listing shows problem symptoms, possible 

causes and corrective actions (if these do not identify 

and correct the problem, contact your dealer or service 

station)

!  switch off the tool and remove the battery before 

investigating the problem

★ Tool operates intermittently

-  internal wiring defective -> contact dealer/service 

station

-  on/off switch defective -> contact dealer/service 

station

★ Motor runs but blades remain stationary

-  internal fault -> contact dealer/service station

★

Cutting blades hot

-  cutting blades blunt -> have blades sharpened

-  cutting blades have dents -> have blades inspected

-  too much friction due to lack of lubricant -> lubricate 

blades

eNVIroNMeNT

• 

Do not dispose of electric tools, batteries, 

accessories and packaging together with household 

waste material

 (only for EU countries)

-  in observance of European Directive 2012/19/EC on 

waste of electric and electronic equipment and its 

implementation in accordance with national law, 

electric tools that have reached the end of their life 

must be collected separately and returned to an 

environmentally compatible recycling facility

-  symbol 

@

 will remind you of this when the need for 

disposing occurs

•  The nickel-metalhydride battery must be kept separate 

from the natural environment and should not be disposed 

of as normal domestic waste (symbol 

#

 will remind you 

of this when the need for disposing occurs)

!  prior to disposal protect battery terminals with 

heavy tape to prevent short-circuit

-  dispose of the batteries at an official collection point 

for batteries

!  batteries may explode when disposed of in fire, 

so do not burn battery for any reason

deClArATIoN oF CoNForMITY 

•  We declare under our sole responsibility that the product 

described under “Technical data” is in conformity with the 

following standards or standardization documents: EN 

60335, EN 60745, EN 61000, EN 55014 in accordance 

with the provisions of the directives 2006/95/EC, 

2004/108/EC, 2006/42/EC, 2000/14/EC, 2011/65/EU

• 

Technical file at

: SKIL Europe BV (PT-SEU/ENG1), 

4825 BD Breda, NL

¹ÊÁÂÆιƼ½ÊÇǾ¼½Æ

ȽʹÌÁÇÆËŵÆ¿Áƽ½ÊÁÆ¿

ÍÊÇȽƓˁ˅ʿ˂ ʽ¼¹Ɠ

Ĺ¾ ÁÂÿʹ¹¾

ÈÈÊÇιĹƹ¿½Ê

24.02.2014 

10

NoIse/VIBrATIoN

•  Measured in accordance with EN 60745 the sound 

pressure level of this tool is 58 dB(A) and the sound 

power level 78 dB(A) (standard deviation: 3 dB), and the