Krups EA8010PE - Инструкция по эксплуатации - Страница 21

If your appliances fitted with our Claris - Aqua Filter System F088 cartridge, please remove the cartridge during the descaling
operation. 
Only use KRUPS scale removal products. You can obtain scale removal products from KRUPS Service Centres.
We cannot be held responsible for any damage that may result from the use of tablets from other brands.

Make certain to protect your work surface during cleaning and scale removal cycles, especially if it is made
of marble, stone or wood.

Start the descaling program by pressing the 

button. The ‘CALC' light becomes constant and the indicator lights 

and

flash. 

Remove and clean the drip tray.
Place a container with a minimum capacity of 0.6 l under the coffee outlets as well as under the steam nozzle 

- Fig. 24

. 

Empty the tank and refill it with warm water up to the line ‘CALC’

- Fig. 33

.

Dissolve a sachet of 

Krups

(40 g) 

F054

descaler in the tank 

- Fig. 33.

Replace the water tank. The indicator light 

switches off.

Press the 

button after carrying out all of these operations.

The first phase (approximately 8 min) begins.

The descaling cycle will start automatically. 
At the end of this phase, the sound signal beeps every 10 seconds and the indicator light

’ flashes.

Empty the used water container and put it back in place.
Empty and rinse the water tank 

- Fig. 34

.

Refill the tank with water and put it back into place. The warning light 

goes out.

Press the button 

again to start the second phase. The sound signal stops.

The second phase (about 6 min) begins. 

The program continues. It rinses the appliance and removes any traces of the descaler. 
At the end of this phase, the sound signal beeps every 10 seconds
Remove and empty your used water container and put it back in place.
Press the 

button again to start the final phase. The sound signal stops.

The final phase (approximately 6 min) begins. 
The program continues. It removes the last particles of descaler. 
When the descaling cycle is finished, the indicator light 

‘CALC’

goes out.

Refill your water tank.

Your appliance is ready for the next use.

If you unplug the appliance during cleaning, press the

button, or there is an electrical power cut, the cleaning program

will start again from the beginning. In this case, another cleaning tablet may be necessary. Make sure to carry out the full
cleaning cycle to ensure good maintenance of your appliance.

The cleaning cycle is intermittent: do not put your hands under the water outlets ‘E’ and ‘W’ while the cycle is in progress.

Long rinsing program – total duration: about 2 minutes

When it is necessary to make a long rinsing program, the appliance warns you of this by flashing the 

‘CLEAN’

and 

‘CALC’

lights.
Remove, fill and replace the water tank.
Place a container with a minimum capacity of 0.6 l under the coffee outlets and the steam nozzle.
Start the long rinsing program by pressing the 

button. The lights 

‘CLEAN’

and 

‘CALC’

become constant and the indicator

light starts 

flashing.

When the long rinse is finished, the lights 

‘CLEAN’

and 

‘CALC’

go out and the indicator light 

becomes constant.

Your appliance is ready for the next use.

The appliance can ask you to empty the coffee ground collector.

To switch the appliance off

You can switch off your appliance at any time. As the appliance is switching off, a double beep is emitted and all of the red
lights flash, one after the other. The appliance has registered your request and will stop as soon as possible.

!

If there is not enough water in the water tank, you will be warned by the     light.
Add the appropriate amount of water to the tank and scale removal will continue automatically.

!

OTHER FUNCTIONS

19

EN

KR_EA80-81_1to84.qxp_Mise en page 1  04/05/2016  14:00  Page19