Krups EA8010PE - Инструкция по эксплуатации - Страница 20

Rinsing out the steam circuit:

Place a container under the steam nozzle and press the 

button for 3 seconds to start a steam circuit rinsing cycle, which

will automatically stop after around 300 ml.

Appliance cleaning program – total duration: about 13 minutes

When a cleaning operation is necessary, the appliance warns you of this by flashing the 

‘CLEAN’

light.

This program is only accessible when the appliance requests it (i.e. approximately every 300 coffees or espressos).

To benefit from the guarantee conditions, it is essential to perform the appliance cleaning cycle when informed
to do so. Be sure to follow the procedure closely, step by step.

Only use KRUPS cleaning tablets. You can obtain cleaning tablets from KRUPS Service Centres.
When the indicator light flashes, you can continue to use the appliance but it is recommended that you carry out the program
as soon as possible.
Start the cleaning program by pressing the 

button. The ‘CLEAN’ light becomes constant and the indicator lights 

and

flash.

Remove, empty and clean the coffee ground collector 

- Fig. 21

.

Remove the coffee drawer

(1)

and wipe clean the area where the coffee drawer

(1)

sits

- Fig. 22

.

Remove, empty and clean the drip tray 

- Fig. 23

.

Put all parts back in place.
The light 

goes out.

Remove, fill and put the water tank back into place.
Place a container with a minimum capacity of 0.6l under the coffee outlets 

- Fig. 24

.

Open the maintenance hatch 

- Fig. 25

and insert a KRUPS cleaning tablet (XS3000) in the cleaning duct 

- Fig. 26

.

Press the 

button to start a cleaning cycle.

The first phase (approximately 10 min) begins.

At the end of this phase, the sound signal emits a beep every

10 seconds and you can empty the used water container and the drip tray.
Put the drip tray and container back in place for the next phase.

Press the 

button again to start the final phase. The sound signal stops.

Final phase (±3 min)

The program continues. It rinses the appliance and removes any traces of cleaner.
When the cleaning cycle is finished, the indicator light 

‘CLEAN’

goes out.

Remove and empty the used water container.
Empty the drip tray and put back into place. 
Refill the water tank.

Your appliance is ready for the next use.

If you unplug the appliance during cleaning, press the

button, or there is an electrical power cut, the

cleaning program will star t again from the beginning. In this case, another cleaning tablet may be
necessary. Make sure to carry out the full cleaning cycle to ensure good maintenance of your appliance.

The cleaning cycle is intermittent: do not put your hands under the water outlets ‘E’ and ‘W’ while the cycle
is in progress.

Only use KRUPS (XS3000) cleaning tablets. We cannot be held responsible for any damage that may result from the use of
tablets from other brands.
You can obtain cleaning tablets from KRUPS Service Centres.

Scale removal program - total duration: about 20 minutes

The quantity of scale deposited depends on the hardness of the water used. The appliance will automatically warn you by
the 

‘CALC’

light coming on when you need to proceed with scale removal.

This program is only accessible when the appliance requests it.

To benefit from the guarantee conditions, it is essential to perform the appliance’s scale removal cycle
when informed to do so. 

Be sure to follow the procedure closely step by step. You can continue to use the

appliance when the light is on, but you are advised to perform the program as soon as possible.

!

If there is not enough water in the water tank when you start the program, the 

light will come on to warn you. Add

the appropriate amount of water to the container and cleaning will continue automatically.

!

!

18

KR_EA80-81_1to84.qxp_Mise en page 1  04/05/2016  14:00  Page18