BRAYER BR1101 - Инструкция по эксплуатации - Страница 6

10

11

en

en

(15) « 

 » counterclockwise to release some 

steam. After that close the steam supply by turning 

the knob (15) « 

 » clockwise until bumping 

«•». Switch the steam supply off by pressing the 

steam supply button (10) «   » and switch the 

coffee maker off.

•  Wait until the coffee maker cools down and remove 

the tip (17) from the cappuccinator pipe (16), wipe 

the outer side of the cappuccinator pipe (16) with a 

soft damp cloth and wash the tip (11) under a water 

jet.

• 

Note: 

Successive making of coffee should be 

performed with an at least 5 min interval.

WARMING THE DRINKS

•  You can warm up your drinks by putting the 

cappuccinator pipe (16) without the tip (17) into the 

cup with the drink.

• 

Press the steam supply button (10) «   », wait until 

the indicator (9) «   » lights up.

• 

Put the cappuccinator pipe (16) without the tip (17) 

into the cup with the drink 

• 

you want to warm up. Carefully turn the steam supply 

control knob (15) « 

 » counterclockwise.

•  Close the steam supply by turning the knob (15) « 

 » clockwise until bumping «•».

• 

Switch the steam supply off by pressing the steam 

supply button (10) «   » again.

•  Switch the coffee maker off by pressing the on/off 

button (11) «   », the indicator (7) «   » will go out.

• 

Note:

 some water or steam may appear from the 

filter holder (5), it is normal.

REMOVING MINERAL SCALE

For effective operation of the coffee maker we 

recommend removing scale every 2-3 months and when 

using “hard” water more often.
1. 

Make sure that all the control buttons (10, 11, 12) 

are in the off position.

2. 

Make sure that the steam supply is closed. To do 

this turn the knob (15) « 

 » clockwise until 

bumping «•».

3. 

Make citric acid solution: 2 teaspoons of acid to 1 

litre of water and pour the solution into the water 

tank (20). Install the tank (20) back to its place.

4. 

Install the coffee filter (6) into the holder (5) having 

preliminary matched the ledge on the filter (6) with 

the groove on the holder (5) and turn the filter (6) 

counter/clockwise to fix the filter. Do not put ground 

coffee into the filter (6).

5. 

Install the filter holder (5) into the coffee maker. The 

holder (5) ledges should match the grooves on the 

boiler « 

 », after that turn the filter holder handle 

(4) to the right until bumping «   ».

6.  Place a suitable cup on the grid (2).

7. 

Insert the power plug into the mains socket.

8. 

Switch the coffee maker on by pressing the on/

off button (10) «   », the indicator (7) «   » will 

light up.

9.  Press the button (12) « 

 » and fill a cup of about 

100 ml capacity with water (it is necessary to drain 

the water from the boiler and fill the boiler with the 

citric acid solution), switch the water supply off by 

pressing the button (12) « 

 » again.

10.  Wait until the indicator (8) « 

 » lights up, then 

switch the water supply on by pressing the button 

(12) « 

 » and fill a cup of about 100 ml capacity, 

press the button (12) « 

 » again to switch the 

water supply off and pour the liquid out of the cup.

11.  After a while repeat the procedure described in 

the paragraph 10 and fill the cup of about 100 ml 

capacity again.

12.  Press the steam supply button (10) «   », wait 

until the indicator (9) «   » lights up. Put a suitable 

bowl under the tip (17) and slightly open the 

steam supply by turning the knob (15) « 

 » 

counterclockwise. Carefully turn the knob (15) « 

 » to the maximal steam release position, 

release the steam for about 1 minute, then close 

the steam by turning the knob (15) « 

 » 

clockwise until bumping «•» and switch the steam 

supply off by pressing the button (10) «   ». 

13. 

Switch the coffee maker off by pressing the on/off 

button (11) « 

 ». Wait for 10-15 minutes.

14.  Perform the steps 10 and 11 at least 3 times.

15.  Repeat the cleaning procedure for the steam 

release channels described in the paragraph 12.

16.  With small intervals, repeat the boiler cleaning 

procedure (paragraph 10) until the citric acid 

solution dissolves in the tank (20) completely.

17. 

Switch the coffee maker off by pressing the on/off 

button (11) «   ».

18. 

Fill the water tank (20) with clear water until 

maximal level and repeat the steps 10, 12 at least 3 

times without the 10-15 minute break.

19. 

Switch the coffee maker off by pressing the on/off 

button (11) «   ».

• 

Note:

 to remove the scale you can use special 

descaling agents for coffee makers and coffee 

machines, strictly following the instructions on their 

usage.

CLEANING THE COFFEE MAKER

•  If there is ground coffee scale remainin in the filter (6) 

openings, clean the filter (6) with a small brush.

•  Wipe the coffee maker body with a soft, slightly damp 

cloth and then wipe the coffee maker body (18) 

dry. Do not use abrasives and solvents to clean the 

coffee maker body.

•  Do not immerse the coffee maker body (18), the 

power cord and the power plug into water or any 

other liquids.

•  Wash the removable parts of the coffee maker with 

warm water and neutral detergent, then rinse them 

and dry.