BRAYER BR1101 - Инструкция по эксплуатации - Страница 4

6

7

en

en

is detected, and after it was dropped, unplug the unit 

and apply to the service center.

•  Transport the coffee maker in the original package.

• 

Keep the unit out of reach of children and disabled

• 

persons.

COFFEE MAKER IS INTENDED FOR HOUSEHOLD 

USE ONLY, DO NOT USE THE COFFEE MAKER FOR 

COMMERCIAL OR LABORATORY PURPOSES.

BEFORE USING THE COFFEE MAKER

After unit transportation or storage at low 

temperature, it is necessary to keep it for at least 

three hours at room temperature.

•  Unpack the coffee maker and remove all the 

packaging materials. 

•  Keep the original package.

•  Check the delivery set.

• 

Read the safety measures and operating 

recommendations.

•  Examine the coffee maker for damages, in case of 

damage do not plug it into the mains.

•  Make sure that the specifications of power supply 

voltage specified on the lower panel of the unit 

correspond to the specifications of your mains. When 

the unit is used in the mains with 60 Hz frequency, it 

does not need any additional settings.

•  Wipe the surface of the coffee maker body with a 

clean, slightly damp cloth to remove dust. 

•  Make sure that all the control buttons (10, 11, 12) are 

in the off position.

•  Make sure that the steam supply is closed. To do this 

turn the knob (15) « 

 » clockwise until bumping 

«•».

•  Before using the coffee maker for the first time, wash 

all removable parts (5, 6, 17, 20, 21) with warm water 

and dry them.

•  Before switching the unit on, make sure that voltage 

of the mains corresponds 

•  to unit operating voltage specified on the unit body. 

When the unit is used in the mains with 60 Hz 

frequency, it does not need any additional settings.

•  Remove the water tank (20), fill it with cold water up 

to the MAX mark and install it back to its place.

• 

Notes: 

- to fill the water tank (20) with water you can lift the 

lid (19), fold it back and pour water into the tank 

(20).

- do not use the lid (19) to carry the water tank (20).

•  Install the coffee filter (6) into the holder (5) having 

preliminary matched the ledge on the filter (6) with 

the groove on the holder (5) and turn the filter (6) 

counter/clockwise to fix the filter.

•  Install the filter holder (5) into the coffee maker. The 

holder (5) ledges should match the grooves on the 

boiler « 

 », after that turn the filter holder handle 

(4) to the right until bumping «   ».

• 

Place a suitable cup on the grid (2).

•  Insert the power plug into the mains socket.

•  Switch the coffee maker on by pressing the on/off 

button (11) «   », the indicator (7) «   » will light up.

•  To fill the boiler with water press the button (12) « 

 », wait for 15-20 seconds, or at the first signs 

of appearance of water in the cup, switch the water 

supply off by pressing the button (12) « 

 » again. 

• 

Wait until the indicator lights up, then switch the 

water supply on by pressing the button (12) « 

 ». 

After the cup is filled with water, press the button (12) 

« 

 » again to switch the water supply off and pour 

the water out of the cup.

• 

Depending on the cup capacity repeat this procedure 

several times until the boiler is clean.

HOW TO MAKE A GOOD ESPRESSO

•  Use ground coffee for espresso coffee makers.

•  Slightly tamp the ground coffee in the filter (6), you 

can do it with the back side of the measuring spoon 

(17).

• 

Coffee strength depends on the quality and grinding 

degree of coffee beans. If coffee is pouring out too 

long, this means the coffee powder is too fine or it is 

tamped too strongly.

THERMOMETER

You can control the temperature by the indicators (8, 9) 

and with the built-in thermometer (13). The thermometer 

(13) scale shows the water temperature in the coffee 

maker.

PREHEATING

•  To make a cup of hot espresso, it is recommended to 

preliminary heat up the coffee filter (6) and the filter 

holder (5).

•  Open the lid (19) and fill the tank (20) with water, or 

remove the tank (20) and fill it with water, then install 

the tank (20) back to its place.

•  Install the coffee filter (6) into the holder (5) having 

preliminary matched the ledge on the filter (6) with 

the groove on the holder (5) and turn the filter (6) 

counter/clockwise to fix the filter.

ATTENTION!

•  Do not remove the filter holder (5) when the 

buttons (10, 12) are pressed.

•  Do not remove the filter holder (5) immediately 

after preparing coffee as there is redundant water 

and steam pressure inside the filter (5), let the 

coffee maker cool down completely.

•  To remove the filter holder (5) turn the handle (4) 

to the left « 

 » and remove the filter holder (5).

AUTO SWITCH OFF FUNCTION

• 

If no actions were performed during 25 minutes 

after switching on, the coffee maker will switch off 

automatically.