Krups Intuition Essential (EA870810) - Инструкция по эксплуатации - Страница 23

41

40

ENGLISH

Please note:

There are 2 preheating times: one for the machine and one for the steam. The 
LED flashes to indicate that the machine has finished preheating. Press “START/
STOP” again to start steam production. See section 

5 - MAKE A MILK RECIPE, 

fig 8.
Caution: risk of burns.

Important: 

Steam production stops automatically depending on the steam time selected 
previously. You can press "START/STOP" before the end of the cycle if the 
amount of milk froth is sufficient.
THE CYCLE DOES NOT STOP IMMEDIATELY.
If you do not press the “START/STOP” button, the machine returns to its initial 
position after 2 minutes.

– The Favourites program is available for the steam function.

Advice and Tips:

To make the milk froth, fill 1/3 of the cup with milk. Immerse the steam nozzle in the milk 
and hold it against the edge of the cup. Tilt the cup 45°. This technique creates a milk 
whirlpool, which makes the optimal amount of foam. By following these tips, you will 
create a barista-quality milk froth ready to be used to make a milky drink.

CLEANING THE STEAM NOZZLE 

Important: 

In order to obtain identical froth each time, we recommend that you carefully 
clean the tube and its connector AFTER EACH USE. Do not wash the steam 
nozzle in the dishwasher.

Danger: 

After using the steam function, the nozzle may be hot, we advise you to wait a 
few moments before handling it.

HOT WATER DRINKS

– Place the cup under the

 STEAM NOZZLE (G).

– Press 

– You can adjust the volume of the drink according to your preference. However, it is not 

possible to make 2 cups at the same time: the “x2” function is not available.

– Press 

. The machine preheats (the lights flash), then the hot water starts to flow. 

– The Favourites function is available. See section 

3- SAVE YOUR FAVOURITE 

SETTINGS / REPROGRAM A FAVOURITE, fig 1 to 6.

GENERAL MAINTENANCE

Carrying out proper maintenance will prolong the life of your machine and preserve the 
authentic taste of your coffee.

Important:

To make things simpler and more efficient, your Krups machine has an automated 
cleaning system: a tablet is all that’s needed! The appliance requires no manual 
maintenance. We guarantee thorough cleaning at high temperatures for a perfect 
coffee every time.

MAINTENANCE OF THE COFFEE GROUNDS COLLECTOR 
AND DRIP TRAY

The drip tray receives the waste water.
The coffee grounds collector receives the grounds extracted.

When do I empty the drip tray? See section 10 – EMPTYING THE DRIP TRAY, fig 1 to 5.

When the floats are in the upper position, indicating that it is too full. 

Important:

It is not dishwasher-safe.

DRINKS MADE USING STEAM

The steam nozzle (G) foams the milk to made a Cappuccino or Café Latte. As the steam 
production requires a higher temperature than for making an espresso, the appliance 
provides an additional preheating phase for the steam. 
For manual milk foaming, use pasteurised or UHT milk from the refrigerator (3 - 5°C). The 
use of special milks (micro filtered, raw, fermented, enriched) or plant milks (rice, oat or 
almond milk) can give results that are less satisfactory in terms of quality and quantity of 
froth.
It is not possible to make 2 cups at the same time: the “x2” function is not available.

The steps for making this drink with steam can be found in section 

5 – MAKE A MILK 

RECIPE, fig 1 to 11.

– The steam nozzle can be removed for deep cleaning. Wash it with water and some 

non-abrasive washing up liquid with a brush. The steps for cleaning the steam nozzle 
can be found in section

 6 – CLEAN YOUR STEAM NOZZLE, Fig 1 to 8.

– To remove any traces of milk from the steam nozzle, place a container under the 

nozzle and launch a hot water drink. Then, take a clean, damp microfibre cloth and 
wipe the nozzle. 

– If steam does not come out, the nozzle may be clogged: unclog with the needle 

supplied. See section 

6- CLEAN YOUR STEAM NOZZLE, Fig 4 and 5.