Krups Arabica EA811810 - Инструкция по эксплуатации - Страница 21

21

EN

Installation of the filter cartridge - total duration: around 2 min

To get the best taste from your coffee and extend your appliance’s service life, we advise you to use only the Claris - 

Aqua Filter System cartridge sold as an accessory.

Fig. 30

 : Mechanism to indicate the month the cartridge was fitted and when to replace it (after 2 months at most).

Installing the cartridge in the appliance. On first use, screw the filter cartridge into the bottom of the water tank

 - Fig. 31

.

Place a 0.6 l container under the steam nozzle.
Press the 

 button for more than 3 seconds (unless the appliance requires a ‘

CLEAN’ 

and/or 

‘CALC’

 maintenance). 

The indicator light 

 flashes.

When the installation of the filter cartridge is finished, the indicator light 

 becomes constant.

Your appliance is ready for the next use.

The Claris cartridge needs to be replaced after about every 50 litres of water or every two months at least. If you are 

using the Claris – Aqua Filter System cartridge, set the water hardness to level 0.

Settings

Connect the appliance to the mains power supply but do not turn it on.

Lift the cup grid by pressing on the back to make it tilt - 

Fig. 25

.

Press the 

 and 

 simultaneously - 

Fig. 27

.

The digital display for parameter setting is under the servicing flap - 

Fig. 28

.

Look down vertically to the bottom of the window - 

Fig. 29

.

Proposed settings order:

1.  Adjust water hardness
2.  Adjust coffee temperature
3.  Adjustment of the auto-off function
4.  Info

1. Setting water hardness

Appliances are pre-set in the factory for hardness level 4.

Before using the appliance for the first time or if you have noted a change in water hardness, it is advisable to adapt the 

appliance to the water hardness. Please contact your water supplier to find out the water hardness in your area.

Degree of 

hardness

0

Verv soft

1

soft

2

moderately hard

3

hard

4

extremely hard

° f

< 5,4°

> 7,2°

> 12,6°

> 25,2°

> 37,8°

°dH

< 3°

> 4°

> 7°

> 14°

> 21°

°e

< 3,75°

> 5°

> 8,75°

> 17,5°

> 26,25°

Settings

0

1

2

3

4

The “water tank” 

 light will come on.

Press the 

 button - 

Fig. 32

 as many times as are needed to select the hardness level for the water used: 0 = very 

soft, 1 = soft, 2 = moderately hard, 3 = hard, 4 = very hard.

To go to the next phase, press the 

 button or to leave the settings mode press 

.

2. Setting the coffee temperature

Appliances are pre-set in the factory to level 2.

The 

‘CALC’

 light comes on.

Press the 

 - 

Fig. 32

 button as many times as are needed to adjust the desired coffee temperature: 1, 2 or 3.

To go to the next phase, press the 

 button or to leave the settings mode, press 

.

3. Setting the automatic electrical power supply cut-off (auto-off)

Appliances are pre-set in the factory to 1 hour.

You can set your appliance to turn off after a pre-programmed number of hours.

The 

‘CLEAN’

 light comes on.

Press the 

 - 

Fig. 32

 button as many times as necessary to select the desired duration: 1 = 1h, 2 = 2h, 3 = 3h, 4 = 4h.

To go to the next phase, press the 

 button, or to leave the settings mode, press 

.