Liebherr KBgw 3864 Premium BioFresh - Инструкция по эксплуатации - Страница 8

Do not install the appliance in a location where it is exposed to

direct radiation of the sun, next to a cooker, heater and similar.
Always  install  the  appliance  with  the  back  directly  against  the

wall.
Do not install the appliance without assistance.
Standard EN 378 specifies that the room in which you install your

appliance must have a volume of 1 m

2

 per 8 g of R 600a refrig-

erant used in the appliance. If the room in which the appliance is

installed is too small, a flammable gas-air mixture may form in the

event  of  a  leakage  in  the  refrigeration  circuit.  The  quantity  of

refrigerant used in your appliance is indicated on the type plate

on the inside of the appliance.

CAUTION

Risk of injury and damage!

The glass door may strike against the wall and be damaged as a

result. The fractured glass may lead to injury!

u

Protect the glass door from striking against the wall. Fit a door

stop, e.g. one made of felt, to the wall.

u

A limiter restricting door opening to 90° can be ordered from

the aftersales service.

WARNING

Fire hazard due to dampness!

If live parts or the mains lead become damp this may cause short

circuits.

u

The appliance is designed for use in enclosed areas. Do not

operate the appliance outdoors or in areas where it is exposed

to splash water or damp conditions.

WARNING

Fire hazard due to refrigerant!

The refrigerant R 600a is environmentally friendly but flammable.

Escaping refrigerant may ignite.

u

Do not damage the piping of the refrigeration circuit.

WARNING

Fire hazard and danger of damage!

u

Do  not  place  appliances  emitting  heat  e.g.  microwaves,

toasters etc. on the appliance!

WARNING

Blocked ventilation openings pose a risk of fire and damage!

u

Always  keep  the  ventilation  openings  clear.  Always  ensure

that the appliance is properly ventilated!

u

Detach the connecting cable from the rear of the appliance,

removing  the  cable  holder  at  the  same  time  because  other-

wise there will be vibratory noise!

u

Remove  the  protective  film  from  the  outside  of  the  appli-

ance.*

u

Evenly apply an agent for care of stainless steel, wiping in the

direction of the grain.*

w

Subsequent cleaning becomes easier as a result.*

u

Remove the protective film from the decorative trims.

u

Remove all transit supports.

u

Dispose of packaging material (see 4.5) .

NOTICE

Risk of damage due to condensate!

u

Do not install the appliance directly alongside a further refrig-

erator/freezer.

u

Align  the  appliance  so  that  it

stands firmly and on a level by

applying  the  accompanying

spanner  to  the  adjustable-

height feet (A) and using a spirit

level.

u

Then support the door: Extend

the  adjustable  foot  at  the  turn

hinge  (B)  until  it  rests  on  the

floor  and  then  make  a  further

90° turn.

If the appliance is installed in a very damp environment, conden-

sate may form on the outside of the appliance.

u

Always see to good ventilation at the installation site.

4.5 Disposing of packaging

WARNING

Danger of suffocation due to packing material and plastic film!

u

Do not allow children to play with packing material.

The packaging is made of recyclable materials:

-

corrugated board/cardboard

-

expanded polystyrene parts

-

polythene bags and sheets

-

polypropylene straps

u

Take the packaging material to an official collecting point.

4.6 Connecting the appliance

NOTICE

Risk of damage to the electronic control system!

u

Do  not  use  stand-alone  inverters  (conversion  of  d.c.  to  a.c./

three-phase) or energy saving plugs.

WARNING

Fire and overheating hazard!

u

Do not use extension cables or multiple socket outlets.

The type of current (alternating current) and voltage at the instal-

lation site have to conform with the data on the type plate  (see

Appliance at a glance).

Connect  the  appliance  only  with  a  properly  installed

socket outlet with earthing contact. The socket outlet

must be fused with 10 A or higher.
It must be easily accessible so that the appliance can

be quickly disconnected from the supply in an emer-

gency.

u

Check the electrical connection.

u

Clean the appliance  (see 6.2) .

u

Plug in the power plug.

4.7 Switching on the appliance

Put the appliance into operation about 2 hours before first loading

food to be frozen.

u

Press On/Off button

 Fig. 3 (3).

w

The temperature display indicates the current temperature.

w

The interior light is on when the door is open.

Putting into operation

8