Stiga Combi 36 - Инструкция по эксплуатации - Страница 70

6

For any doubts or problems, please do not hesitate to con

-

tact your nearest Customer Service Centre or Your Dealer.

4. ROUTINE MAINTENANCE

Store the lawnmower in a dry place.

 IMPORTANT 

 Routine and accurate maintenance is es-

sential  in  maintaining  original  machine  safety  and  perfor

-

mance levels.

Adjustments or maintenance operations must only be per

-

formed with the motor switched off and the machine discon

-

nected from the mains power supply.

1)   Wear  strong  protective  gloves  before  cleaning,  main

-

taining or adjusting the machine.

2)   Accurately  wash  the  machine  with  water  after  cutting, 

remove grass debris and mud accumulated in the chas

-

sis  to  prevent  it  from  drying  and  causing  problems  the 

next time the lawnmower is used.

3)   Always make sure the air intakes are free of debris.

 4.1    Vertical storage (Model 380 - 420)

If  necessary,  the  machine  can  be  stored  vertically,  hang

-

ing from a hook.

WARNING! 

 Make sure the hook and its fasten-

ing system are adequate and able to sustain the ma-

chine’s weight; exercise caution and make sure chil-

dren or animals do not climb on the machine, weighing 

down the hook.

Fasten the machine so that the cutting means faces a 

wall or is properly covered, so it is not dangerous in 

the event of accidental contact with persons, children 

or animals.

To  store  the  machine  vertically,  release  the  levers  (1  – 

Type  “III”)  or  loosen  the  knobs  (2  –  Type  “IV”)  and  turn 

the  handle  forward  so  the  tooth  marked  with  «>»  matches 

EXCLUSIVELY  with  the  compartment  marked  «S»  of  the 

teeth,  then  lock  the  levers  (1  -  Type  “III”)  or  the  knobs  (2 

– Type “IV”).

The position must be the same for both sides. 

 4.2   Cutting means maintenance 

It is best if all interventions on the cutting means are done 

at a specialised Centre that has the most appropriate tools 

and equipment.

Only cutting means bearing the code indicated in table on 

page ii must be used on this machine.

Given  product  evolution,  the  above  mentioned  cutting 

means  may  be  replaced  in  time  with  others  having  similar 

interchangeable and operating safety features. 

Reassemble  the  cutting  means  (2)  with  the  code  facing 

the ground, following the steps indicated in the illustration.  

Tighten the central screw (1) using a dynamometric key 

calibrated at 30 Nm (for model 340) or 16-20 Nm (for model 

380 - 420).

 4.3  Cleaning the machine

Do  not  spray  water  onto  the  motor  and  electrical  compo

-

nents and prevent them from getting wet.

Do not use aggressive liquids to clean the chassis.

 4.4    Cleaning the air intakes 

Remove dust and grass residue from the air intake once a 

month, blowing compressed air onto the mesh.

5. DIAGNOSTICS

What to do if ....

Problem description

Corrective Action

1.  The electric lawnmower doesn’t work

The machine has no power 

supply 

Check the electrical 

connection

2.  The electric lawnmower trips the power supply.

The mains socket 

amperage is insufficient

Connect the machine 

to a mains socket with 

sufficient amperage

Other electrical appliances 

are being used

Do not connect other 

appliances to the same 

mains socket at the same 

time

3. The cut grass is not collected in the grass catcher

The cutting means has 

received a knock

Have the cutting means 

sharpened or replace it

Check the fins that direct 

the grass towards the 

grass catcher

The inside of the chassis 

is dirty

Clean the inside of the 

chassis to ease the grass 

discharge towards the 

grass catcher 

4. Mowing is difficult

The cutting means is not in 

good condition

Have the cutting means 

sharpened or replace it

5. The machine starts to vibrate abnormally

Damaged or loose parts

Stop the machine and 

disconnect the plug from 

the socket.

Inspect for damage

Check for and tighten any 

loose parts

Have all checks, repair 

work and replacements 

carried out by a specialized 

Centre only