Ryobi RLM53190YV 5133003672 - Инструкция по эксплуатации - Страница 9

English

7

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

UK

TR

not overfill.

NOTE: 

When checking the oil level, seat the dipstick in the 

oil 

fi

 ll hole but do not screw in.

5.  Reinstall and secure the oil cap/dipstick by turning it 90° 

clockwise.

To check engine oil:

■

Be sure mower is level and area around oil cap/dipstick 
is clean.

■

Remove the oil cap/dipstick. Wipe clean and reseat in 
the oil 

fi

 ll hole but do not screw in.

■

Remove the oil cap/dipstick again and check the oil 
level. Add oil as needed.

STARTING OR STOPPING THE MOWER

See figure 5.

 WARNING

Never start or run the engine inside a closed or poorly 
ventilated area; breathing exhaust fumes can kill.

NOTE

: The engine is provided with a shut-off valve. Turn 

the fuel off at the conclusion of mowing.

Starting the engine

1.  Open the fuel valve.
2.  Set the variable throttle lever to the fastest speed.
3.  Press the primer bulb 3 times.

NOTE:

 This step is not usually necessary when starting 

an engine that has already run for a few minutes.

4.  Hold the power lever bar down against the handle.
5.  Pull the starter grip until the engine starts. Release the 

starter cord slowly so the rope does not snap back.

NOTE:

 It may be necessary to repeat the priming steps 

in cooler weather. In warmer weather, overpriming may 
cause flooding and the engine will not start. If you do 
flood the engine, wait a few minutes before attempting 
to start and do not repeat priming steps.

Stopping the engine

1.  Release the power lever and allow the engine to come 

to a complete stop.

2.  Close the fuel valve.

USING THE VARIABLE THROTTLE

See figure 19.

■

The variable throttle lever on the handle allows the user 
to set variations in the engine speed only, and it should 
be set in the fastest speed when starting the mower and 
when cutting grass.

■

The variable throttle lever will not stop the engine. The 
power lever on the handle must be released to stop the 
engine.

USING THE VARIABLE TRANSMISSION

See figure 20.

■

The variable transmission lever on the handle allows 
the user to set variations in the transmission speed.

■

Do not change lever position if the product is not 
running; otherwise, the lever may be damaged.

■

For taller grass, reduce the transmission speed and 
increase the engine speed.

PROPELLING THE PRODUCT

See figure 6. 

■

To self-propel: Hold down the power lever while slowly 
pulling the self-propel bail towards the handle. Release 
the self-propel bail to stop the wheel drive.

■

To manually propel: Hold down the power lever. Do not 
engage the self-propel bail.

NOTE:

 The product will start to run when the self-propel 

bail is engaged.

SETTING BLADE HEIGHT

See figure 7.

When shipped, the wheels on the mower are set to a low- 
cutting position. Before using the mower for the 

fi

 rst  time, 

adjust the cutting position to the height best suited for your 
lawn. The average lawn should be between 38 mm to 50 
mm during cool months and between 50 mm and 76 mm 
during hot months.

To set the blade height:

■

Stop the product and wait for the blade to come to a 
complete stop.

■

To raise the blade height, grasp the height adjustment 
lever and move it toward the back of the mower.

■

To lower the blade height, grasp the height adjustment 
lever and move it toward the front of the mower.

SETTING HANDLE HEIGHT AND ANGLE

See figure 8.

The height of the handle can be easily adjusted for operator 
preference.

To adjust the handle height:

■

Remove the quick-release knob.

■

Slide out the quick-release lever and adjust the height 
to the other opening.

■

Reinstall the quick-release fastener. Tighten the quick-
release knob.

■

Repeat on the other side of the handle.

To adjust the handle angle:

■

Release the lower quick-release fasteners.