Ryobi RLM53190SV 5133002556 - Инструкция по эксплуатации - Страница 8

English

6

3.  Release the rear door. When installed correctly, the 

hooks on the grass catcher will rest securely on the 
hinge rod of the rear door.

4.  Ensure the rear door is fully engaged on the grass 

catcher. Make sure that there is no gap between the 
rear door and the grass catcher.

INSTALLING SIDE DISCHARGE DEFLECTOR (FOR 
SIDE DISCHARGE OPERATION)

See figure 9.

NOTE:

 When using the side discharge de

À

 ector, do not 

install the grass catcher. The mulching plug should remain 
installed.

1.  Lift the side discharge door.
2.  Align the hooks on the deflector with the hinge rod on 

the underside of the door.

3.  Lower the deflector until the hooks are secured on the 

mulch door hinge rod.

4.  Release the deflector and side discharge door.

OPERATION

FUEL AND REFUELLING

 WARNING

Always handle petrol with care; it is highly flammable.

Ŷ

Use fresh fuel.

Ŷ

Store fuel in containers specifically designed for this 
purpose.

Ŷ

Always refuel outdoors where there are no sparks and 
flames. Do not inhale fuel vapour. Do not smoke. Stay 
away from open 

À

 ames and sparks when 

¿

 lling fuel tank 

or when handling fuel.

Ŷ

Do not let petrol or oil come in contact with your skin.

Ŷ

Keep petrol and oil away from the eyes. If petrol or oil 
comes in contact with the eyes, wash them immediately 
with clean water. If irritation is still present, see a doctor 
immediately.

Ŷ

Immediately clean up spilled petrol.

FILLING THE TANK

See figure 5.

 WARNING

Always shut off engine and allow it to cool for 5 minutes  
before refuelling. Never remove the cap of the fuel tank 
or add petrol to a machine with a running or hot engine. 
Move at least 9 m (30 ft) from the refuelling site before 
starting the engine. Do not smoke. Failure to heed this 
warning could result in serious personal injury. 

 WARNING

Do not overfill. Fill the fuel tank to 25 mm below the top 
of the fuel neck. After fueling, never tilt the mower more 
than 25 degrees for this could result in fuel leakage and 
risk of fire, etc.

1. Clean surface around the fuel cap to prevent 

contamination.

2.  Slowly loosen the fuel cap to release pressure and to 

keep fuel from escaping around the cap. Rest the cap 
on a clean surface.

3.  Carefully pour petrol into the tank. Avoid spillage.
4.  Clean and inspect the gasket. Replace and secure all 

fuel and container caps.

5.  Wipe up any fuel spillage. Move 9 m away from the 

refuelling site before starting the engine.

NOTE:

 It is normal for smoke to be emitted from a new 

engine during and after 

¿

 rst use.

ADDING/CHECKING ENGINE OIL

See figure 5.

Engine oil has a major in

À

 uence on engine performance 

and service life. For general, all-temperature use, SAE 
10W-30 is recommended. Always use a 4-cycle motor oil 
that meets or exceeds the requirements for API service 
classi

¿

 cation SJ.

NOTE: 

Non-detergent or 2-cycle engine oils will damage 

the engine and should not be used.

To add engine oil:

1.  Be sure the mower is level and the area around the oil 

cap/dipstick is clean.

2.  Remove the cap and the seal from the oil bottle.
3. Open the oil cap/dipstick by turning it 90° 

counterclockwise. Remove the oil cap/dipstick.

4.  Slowly add oil. Fill to the “Full” line on the dipstick. Do 

not overfill.

NOTE: 

When checking the oil level, seat the dipstick in the 

oil 

¿

 ll hole but do not screw in.

5.  Reinstall and secure the oil cap/dipstick by turning it 90° 

clockwise.

To check engine oil:

Ŷ

Be sure mower is level and area around oil cap/dipstick 
is clean.

Ŷ

Remove the oil cap/dipstick. Wipe clean and reseat in 
the oil 

¿

 ll hole but do not screw in.

Ŷ

Remove the oil cap/dipstick again and check the oil 
level. Add oil as needed.

STARTING OR STOPPING THE MOWER

See figure 5.