Einhell TP-RO 18 Li (4350410) - Инструкция по эксплуатации - Страница 28

GB

- 28 -

edge of the workpiece.

• 

 Perform the cut as explained in section 6.4.

6.8  Making cuts freehand

The cordless router/palm router can also be used 

without any guides. You can use it freehand on 

creative jobs such as the production of lettering.

• 

 Use a very flat cutter setting for this purpose!

• 

 Check the direction in which the cutter is tur-

ning while you machine the workpiece (Fig. 

18).

6.9  Cutting shapes and edges (Fig. 19)

• 

 Special cutters with a guide ring can be used 

for cutting shapes (a) and edges (b).

• 

 Fit the cutter.

• 

 Carefully move the machine against the work-

piece.

• 

 Using gentle pressure, move the guide jour-

nal or ball bearing (c) along the workpiece.

Cordless palm router

With the help of the routing guide (32) you 

can also perform edge cuts.

• 

 Fit the routing guide (32) as explained in Fig. 

5.9.

• 

 Place the cordless palm router on the workpi-

ece and adjust the height of the routing guide 

(32) so that the ball bearing (a) lies under-

neath the cutter.

• 

 Now undo the fastening screw (b) and then 

use the adjustment screw (c) to set the lateral 

feed of the cutter.

• 

 Retighten the fastening screw (b).

Warning:

For deep cuts, carry out the work in several 

steps according to the material in question. 

Hold the equipment in two hands during all 

cutting work.

6.10 Charging the LI battery pack (Fig. 22-23)

1.  Remove the battery pack (k) from the handle, 

pressing the pushlock buttons (l) downwards 

to do so.

2.  Check that your mains voltage is the same as 

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

(6) into the mains socket outlet. The green 

LED will then begin to 

fl

 ash.

3.  Push the battery pack onto the battery char-

ger.

In section “Charger indicator” you will 

fi

 nd a table 

with an explanation of the LED indicator on the 

charger.

If the battery pack fails to become charged, ple-

ase check

• 

 whether there is voltage at the socket-outlet

• 

 whether there is proper contact at the char-

ging contacts on the charger.

If the battery still fails to become charged, please 

return

• 

 the  charger

• 

 the battery pack

to our Customer Service Department.

To ensure that items are properly packaged 

and delivered when you send them to us, 

please contact our customer service or the 

point of sale at which the equipment was 

purchased.

When shipping or disposing of batteries and 

cordless tools, always ensure that they are 

packed individually in plastic bags to prevent 

short circuits and 

fi

 res.

To ensure that the battery pack provides long ser-

vice, you should take care to recharge it promptly. 

You must recharge the battery pack when you 

notice that the performance of the device drops. 

Never allow the battery pack to become fully di-

scharged. This will cause it to develop a defect.

6.11 Battery capacity indicator 

(Fig. 24/Item n)

Press the battery capacity indicator switch (o). 

The battery capacity indicator (n) shows the char-

ge status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED 

fl

 ashes:

The battery is empty, recharge the battery.

All LEDs blink:

The battery temperature is too low. Remove the 

battery from the equipment, keep it at room tem-

perature for one day. If the fault reoccurs, this me-

ans that the rechargeable battery has undergone 

exhaustive discharge and is defective. Remove 

Anl_TP-RO_18_Li_BL_SPK13.indb   28

30.06.2022   09:07:26