Einhell TP-RO 18 Li (4350410) - Инструкция по эксплуатации - Страница 25

GB

- 25 -

and retighten the fastening screw for the rou-

ting guide (25).

• 

 Set the parallel stop (34) to the required di-

mension and secure it in place with the wing 

screw (c).

5.4  Fitting the compass point (Fig. 5/Item 33) 

• 

 You can cut circular areas using the compass 

point (33).

• 

 To do so, undo the wing nut (c) and remove 

the front section of the parallel stop (34). 

• 

 Screw-fit the compass point (33) on the par-

allel stop (34) as shown in Fig. 5. Now fit the 

parallel stop (34) together with the compass 

point (33) on the router. 

• 

The procedure for fitting is the same as de-

scribed in section 5.3 except that the parallel 

stop (34) must be turned through 180° so that 

the compass point (33) points downwards 

(Fig. 5).

• 

 Set the required radius between the compass 

point (33) and the cutter.

• 

 Position the compass point (33) in the center 

of the circle you wish to cut.

5.5  Fitting and using the copy slee-

ve (Only for the palm router!) 

(Fig. 6-9/Item 29) 

• 

 Remove the four recessed head screws (d) 

from the bottom of the palm router insert and 

take off the cover (e) (Fig. 6).

• 

 Insert the copy sleeve (29) as shown in Fig. 7.

• 

 Refit the cover (e) using the four recessed 

head screws (d). 

• 

 The copy sleeve (29) will be guided along the 

template (g) by the guide ring (f).

• 

 To obtain an exact copy the workpiece (h) 

must be larger by the difference between the 

“external edge of the guide ring” and the “ex-

ternal edge of the cutter” (i).

5.6  Fitting/removing the cordless routing unit 

(Fig. 10-11)

Warning! Remove the battery.

Cordless router

• 

 To insert the cordless routing unit (1) in the 

router insert (35), first undo the fastening 

screw for the routing unit (22) and then insert 

the cordless routing unit (1).

• 

 Now you must retighten the fastening screw 

for the routing unit (22).

Cordless palm router

• 

 To insert the cordless routing unit (1) in the 

palm router insert (36), first undo the faste-

ning screw for the depth adjuster (23) and 

then insert the cordless routing unit (1).

• 

 Then use the height adjuster (24) and the 

scale (38) to set the required cutting depth.

• 

 Finally retighten the fastening screw for the 

depth adjuster (23).

5.7  Fitting/removing the cutting tool 

(Fig. 12- 16)

Warning! Remove the battery.

Caution! When you have 

fi

 nished working 

with the router, the cutting tool will stay very 

hot for a relatively long time!

Caution! Cutters are very sharp. Wear protec-

tive gloves at all times when handling cutting 

tools.

• 

 To make it easier to change the cutter, re-

move the cordless routing unit (1) from the 

respective insert as described in section 5.6

• 

 Cutters with a shaft diameter of 6 mm and 8 

mm can be used in the cordless router/palm 

router. Most cutters are available in both si-

zes.

• 

 You can use cutters made of the following 

materials:

- HSS -

 suitable for cutting softwood

- TCT -

 suitable for cutting hardwood, particle 

board and plastic

• 

 Select the appropriate cutting tool for the job 

in hand.

• 

When using the cutters for the first time:

Remove the plastic packaging from the cutter 

heads.

• 

 Clean the nut, clamp and shaft of the cutter 

before fitting it.

• 

 Undo the clamp nut (6) using the two open-

ended wrenches (28).

• 

 If a cutter is already fitted in the clamp 

(30/31), remove it.

• 

 Select the appropriate cutting tool for the job 

in hand.

• 

 Select the appropriate clamp (30/31) for the 

cutter (i) you want to use.

• 

 Now insert the clamp (30/31) in the cutting 

spindle (Fig. 13).

• 

 Refit the clamp nut (6) (Fig. 14).

• 

 Guide the cutter shaft into the clamp (Fig. 15).

• 

 While holding the spindle lock (5) in pressed 

position, screw the clamp nut (6) hand-tight 

(Fig. 15).

Anl_TP-RO_18_Li_BL_SPK13.indb   25

30.06.2022   09:07:25