WORX WG368E - Инструкция по эксплуатации - Страница 17

Cordless Chain Saw 

EN

17

motor will overload and can burn out. It 
will do the job better and safer at the rate 
for which it was intended.

8.  Remove the saw from a cut with the saw 

running at full speed. Stop the saw by 
releasing the On/Off Switch. Make sure the 
Chain has stopped before setting the saw 
down.

9.  Keep practicing on scrap logs in a secure 

working area until you get the hang of 
it and can saw with ease, using a fluid 
motion and a steady cutting rate.

Kickback safety devices on this saw

This saw has a low-kickback chain and 
reduced kickback Guide Bar. Both items 
reduce the chance of kickback. However, 
kickback can still occur with this saw.
The following steps will reduce the risk of 
kickback.
•   Use both hands to grip saw while saw is 

running. Use firm grip. Thumbs and fingers 
must wrap around saw handles.

•   Keep all safety items in place on saw. 

Make sure they work properly.

•   Do not overreach or cut above shoulder 

height.

•   Keep solid footing and balance at all times.
•   Stand slightly to left side of saw. This keeps 

your body from being in direct line with 
chain.

•   Do not let guide bar nose touch anything 

when chain is moving.

•   Never try cutting through two logs at same 

time. Only cut one log at a time.

•   Do not bury the Guide Bar nose or try 

plunge cut (boring into wood using guide 
bar nose).

•   Watch for shifting of wood or other forces 

that may pinch chain.

•   Use extreme caution when reentering a 

previous cut.

•   Use only the low-kickback chain and guide 

bar that were supplied with this chain saw. 

•   Never use a dull or loose chain. Keep chain 

sharp with proper tension.

How to use saw safely

1.   Use the chain saw only with secure 

footing.

2.  Hold the chain saw at the right-hand side 

of your body (See Fig. L).

3.  The Chain (8) must be running at full speed 

before it makes contact with the wood.

4.   Use the metal Gripping Teeth (9) to secure 

the saw onto the wood before starting to cut.

5.  Use the Gripping Teeth as a leverage point 

(a) while cutting. (See Fig. M)

6.  Do not operate the chain saw with arms 

fully extended, attempt to saw areas which 
are difficult to reach, or stand on a ladder 
while sawing (See Fig. N). 

Cutting wood under tension (See fig. O)

WARNING: When cutting a limb 

that is under tension, use extreme 

caution. Be alert  for wood springing 

back. When wood tension is released, 

limb could spring back and strike 

operator causing severe injury or death.

When sawing logs supported on both ends, 
start the cut from above(Y) about 1/3 of the 
diameter into the log and then finish the cut 
(Z) from below, in order to avoid contact of 
the chain saw with the ground. When sawing 
logs supported on only one end, start the cut 
from below (Y) about 1/3 of the diameter into 
the log and finish the cut from above (Z) in 
order to avoid log splitting or jamming of the 
chain saw.

Felling trees (See Fig. P)

Always wear hard hat to protect head 

against falling branches.

The chain saw can only be used to fell 

trees smaller in diameter than the length 

of the guide bar.

 Secure work area. Ensure no persons 

or animals are in the vicinity of the 

falling tree.

Never attempt to free a jammed saw 

with the motor running. Use wooden 

wedges to free chain and guide bar.

When cutting and felling operations are being 
performed by two or more persons, at the 
same time, the felling operations should be 
separated from the cutting operation by a 
distance of at least twice the height of the 
tree being felled. Trees should not be felled in 
a manner that would endanger any person,