WORX WG368E - Инструкция по эксплуатации - Страница 15

Cordless Chain Saw 

EN

15

TENSIONING CHAIN

New saw chains will stretch. Check chain 
tension frequently when first used and tighten 
when Chain becomes loose around the Guide 
Bar (7).

WARNING:

Remove the battery 

from the tool before adjusting saw 

chain tension.

WARNING: Cutting edges on chain 

are sharp. Use protective gloves 

when handling chain.

WARNING: Maintain proper chain 

tension always. A loose chain will 

increase the risk of kickback. A loose 

chain may jump out of guide bar groove. 

This may injure operator and damage 

chain. A loose chain will cause chain, 

bar, and sprocket to wear rapidly.

1.   Place the chain saw on any suitable flat 

surface.

2.  Turn the Chain Tensioning Knob (10) 

clockwise until it is hand tight. The tension 
is automatically set while the Chain 
Tensioning Knob is being tightened.

  The ratchet mechanism (a) prevents the 

chain tension from loosening. (See Fig. F1)

3.  Double check the tension set by the 

automatic  Chain Tensioning  Knob. The 
correct chain tension is reached when the 
Chain (8) can be raised approx. 3-6mm 
from the Guide Bar (7) in the center (the 
chain links should just remain in the bar 
track). This should be done by using one 
hand to raise the chain against the weight 
of the machine. (See Fig. F2)

  Use a screwdriver to move chain around 

Guide Bar to ensure kinks do not exist. The 
chain should rotate freely. (See Fig.  F3 )

4.  When the chain looses, unscrew the Chain 

Tensioning Knob absolutely and then 
Screw on the cover plate with the locking 
knob tightly again.

LUBRICATION

IMPORTANT: He chain saw is 

not supplied filled with oil. It is 

essential to fill with oil before use. Never 

operate the chain saw without chain 

oil or at an empty oil tank level, as this 

will result in extensive damage to the 

product.

NOTE:

 Chain life and cutting capacity depend 

on optimum lubrication.  Therefore, the chain 
is automatically oiled during operation. 

Filling oil tank:

1.   Set chain saw on any suitable surface with 

Oil Filler Cap (4) facing upward.

2.  Clean area around the Oil Filler Cap with 

cloth unscrew cap.

3.  Add bar and chain oil until reservoir is full. 

ISO VG32 Bar and chain oil of any brand 
can be used.

4.  Avoid dirt or debris entering oil tank, refit 

the Oil Filler Cap and tighten.

IMPORTANT: To allow venting of 

the oil reservoir, small breather 

channels are provided between the oil 

filler cap and the strainer, to prevent 

leakage ensure machine is left in a 

horizontal position (Oil Filler Cap (4) 

uppermost) when not in use.

It is important to use only the 

recommended oil to avoid damage to the 

chain saw. Never use recycled/old oil. 

Use of non approved oil will invalidate 

the warranty.

CHECKING  THE AUTOMATIC OILER

Proper functioning of the automatic oiler can 
be checked by running the chain saw and 
pointing the tip of the Guide Bar (7) towards a 
piece of cardboard or paper on the ground. 
If an increasing oil pattern develops on the 
cardboard, the automatic oiler is operating 
fine. If there is no oil pattern, despite a full 
oil reservoir, contact WORX customer service 
agent or WORX approved service agent.

CAUTION:

 Do not touch the ground 

with the chain. Ensure safety clearance 

of 30cm.

OPERATION

1. BEFORE USING YOUR CORDLESS 

TOOL

ATTENTION: The charger and 

battery pack are specially designed 

to work together so do not attempt to 

use any other devices. Never insert or