WORX WG303E - Инструкция по эксплуатации - Страница 16

Chain saw 

En

17

16

17

16

the operator or bystanders.
Particular attention must be given when 
sawing sideward, slanted or during length 
cuts, as the spiked bumper usually can not be 
applied.

To avoid kickback:

- Saw with guide bar at a flat angle.
- Never work with a loose, widely stretched or 
the heavily worn out chain.
- Ensure chain is sharpened correctly.
- Never saw above shoulder height.
- Never work with the tip of the guide bar.
- Always hold the chain saw firmly with both 
hands.
- Always use a low kickback chain.
- Apply the metal gripping teeth for leverage.
- Ensure correct chain tension.  

General behavior

Always hold the chain saw firmly with both 
hands. Front grip with the left hand and 
rear grip with the right hand. Fully grip both 
handles at all times during operation. Never 
operate chain saw using only one hand. 
Ensure power cord is located to the rear, away 
from the chain and wood and so positioned 
that it will not be caught on branches or the 
like during cutting.  (See Fig. G)
Use the chain saw only with secure footing. 
Hold the chain saw at the right-hand side of 
your body. (See Fig. I)
The chain must be running at full speed 
before it makes contact with the wood. Use 
the metal gripping teeth to secure the saw 
onto the wood before starting to cut. Use 
the gripping teeth (9) as a leverage point “a” 
while cutting. (See Fig. J)
Reset the gripping teeth at a low point when 
sawing thicker logs by pulling the chain 
saw slightly backwards until the gripping 
teeth release, and reposition at lower level 
to continue sawing. Do not remove the saw 
completely from the wood.
Do not force the chain while cutting, let the 
chain do the work, using the gripping teeth to 
apply minimal leverage pressure.
Do not operate the chain saw with arms fully 
extended or attempt to saw areas which are 
difficult to reach, or on a ladder. Never use the 
chain saw above shoulder height. (See fig. K)

Sawing is optimized when the chain speed 
remains steady during cutting.
Beware when reaching the end of the cut. The 
weight of the saw may change unexpectedly 
as it cuts free from the wood. Accidents can 
occur to the legs and feet.
Always remove the saw from a wood cut 
while the saw is running.

Cutting logs  

Observe the following safety instructions:
Support logs so that the face sides at the 
cut do not close in against each other, which 
would result in the chain being jammed or 
pinched. (See Fig. I,L)
Position and set short logs safety prior to 
sawing. Saw only wood or wooden objects. 
When sawing, always take care to avoid 
hitting stones, nails, ect, as these could be 
thrown up or cause damage to the chain or 
serious injury to the operator or bystanders.
Keep a running saw clear or wire fencing or 
the ground.
Use of the saw to thin out branches or bushes 
is not approved.
Length cuts must be carried out with care, 
as leverage with the gripping teeth (9) is not 
possible. Saw at a flat angle to avoid kickback.
When working on a slope, operate above or to 
the side of the trunk or laying tree.
Be careful not to trip over tree stumps, 
branches, roots, etc.

Cutting wood under tension (See Fig. L)

There is a high risk of accidents when sawing 
wood, branch or trees under tension. Be 
extremely careful.
Leave saw jobs like these to professionals.
When sawing logs supported on both ends, 
start the cut from above(Y) about 1/3 of the 
diameter into the log and then finish the cut 
(Z) from below, in order to avoid contact of 
the chain saw with the ground. When sawing 
logs supported on only one end, start the cut 
from below (Y) about 1/3 of the diameter into 
the log and finish the cut from above (Z) in 
order to avoid log splitting or jamming of the 
chain saw.