Ryobi RY36CSX40B-0, MAX POWER 36В (5133004898) - Инструкция по эксплуатации - Страница 8

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national 
provisions and regulations.
Follow all special requirements on packaging and labelling 
when transporting batteries by a third party. Ensure that 
no batteries can come in contact with other batteries 
or conductive materials while in transport by protecting 
exposed connectors with insulating, non-conductive caps 
or tape. Do not transport batteries that are cracked or 
leaking. Check with the forwarding company for further 
advice.

MAINTENANCE

■

Use only original manufacturer’s replacement parts, 
accessories, and attachments. Failure to do so 
can cause possible injury, can contribute to poor 
performance, and may void your warranty.

■

Servicing requires extreme care and knowledge 
and should be performed only by a qualified service 
technician. Have the product serviced by an authorised 
service centre only.

■

You may make adjustments or repairs described in this 
manual. For other repairs, have the product serviced by 
an authorised service centre only.

■

Consequences of improper maintenance, removal, or 
modification of safety devices may cause the product to 
not function correctly, increasing the potential for serious 
injury. Keep the product professionally maintained.

■

Sharpening the chain safely is a difficult precision task 
that should be performed only by experienced skilled 
professionals. Therefore, the manufacturer strongly 
recommends that a worn or dull chain is replaced with 
a new one, available at your authorised service centre. 
The part number is available in the product specification 
table in this manual.

■

Follow the instructions for lubricating and chain tension 
checking and adjustment.

■

After each use, clean the plastic parts with a soft, dry 
cloth.

■

Check all nuts, bolts, and screws at frequent intervals 
for security to ensure that the product is in safe working 
condition. Any part that is damaged should be properly 
repaired or replaced by an authorised service centre.

Maintenance schedule

Daily check

Bar lubrication

Before each use

Chain tension

Before each use and 
frequently

Chain sharpness

Before each use
(visual check)

For damaged parts

Before each use

For loose fasteners

Before each use

Chain brake function 

Before each use

Inspect and clean

Bar

Before each use

Complete saw

After each use

Chain brake

Every 5 hours of operation

KNOW YOUR PRODUCT

See page 227.

1. Saw chain
2. Guide bar
3.  Front hand guard/Chain brake
4. Front handle
5. Rear handle
6. Combination wrench
7. Oil cap
8. Chain catcher
9.  Guide bar cover
10. Chain tensioning screw
11. Sprocket cover
12. Switch trigger
13. Trigger release
14. Lubricant flow screw
15. Spiked bumper

SAFETY DEVICES

Chain brake

Chain brakes are designed to quickly stop the chain from 
rotating. When the chain brake lever/hand guard is pushed 
towards the bar, the chain should stop immediately. A 
chain brake does not prevent kickback. It only lowers the 
risk of injury should the chain bar contact the operator’s 
body during a kickback event. The chain brake should be 
tested before each use for correct operation in both the run 
and brake positions.

WARNING!

 If the chain brake does not stop the chain 

immediately, or if the chain brake does not stay in the 
run position without assistance, take the product to an 
authorised service centre for repair before use.

Chain catcher

The chain catcher prevents the saw chain from being 
thrown back towards the operator if the saw chain comes 
loose or breaks.

Guide bars

Generally, guide bars with small radius tips have a somewhat 
lower potential for kickback. Use a guide bar and matching 
chain that is just long enough for the job. Longer bars 
increase the risk of loss of control during sawing. Regularly 
check the chain tension. When cutting smaller branches 
(less than the full length of the guide bar) the chain is more 
likely to be thrown o

ff

  if the tension is not correct.

Low-kickback saw chain

The low-kickback saw chain helps to reduce the possibility 
of a kickback event.
The rakers (depth gauges) ahead of each cutter can 
minimise the force of a kickback reaction by preventing the 
cutters from digging in too deeply. Use only replacement 
guide bar and chain combinations that are recommended 
by the manufacturer.
As saw chains are sharpened, they lose some of the low-
kickback qualities, and extra caution is required. For your 
safety, replace saw chains when cutting performance 
decreases.

8

| English