Ryobi RY36CSX40B-0, MAX POWER 36В (5133004898) - Инструкция по эксплуатации - Страница 10

GETTING STARTED

See page 228.

1.  Wear Personal Protective Equipment (PPE).

Wear full eye protection, ear protection, non-slip 
heavy-duty gloves, substantial footwear, and protective 
clothing at all times while operating the product. Do not 
operate the product when barefoot or wearing open 
sandals.

2.  Remove the parts from the packaging. Assemble the 

product.

WARNING!

 If any parts are damaged or missing, 

do not operate the product until the parts are replaced. 
Failure to heed this warning could result in serious 
personal injury.
Place the chain drive links into the bar groove. Position 
the chain so that there is a loop at the back of the bar.
The saw chain should face in the direction of chain 
rotation. If the chain faces backwards, turn the loop 
over. 

3.  Loosen the bar mounting nuts. Remove the nuts and 

sprocket cover.
Hold the chain in position on the bar, and place the loop 
around the drive sprocket. Lower the bar so that the 
bolts go through the slot in the bar. 

4.  Reinstall the sprocket cover. Install and hand-tighten 

the bar mounting nuts. The guide bar must be free to 
move for chain tension adjustment.

5.  Adjust the chain tension. Turn the chain tensioning 

screw using the combination wrench. Frequently check 
the chain tension while adjusting.

–

To increase the chain tension, turn the chain 
tensioning screw clockwise.

–

To reduce the chain tension, turn the chain 
tensioning screw counterclockwise.

NOTE: 

The chain tension is correct when the gap 

between the cutter in the chain and the bar is between 
4 and 5 mm for the RY36CSX30B and between 5 and 
6 mm for RY36CSX40B. Pull the chain in the middle 
of the lower side of the bar downwards (away from the 
bar), and measure the distance between the bar and 
the chain cutters.

NOTE:

 The temperature of the chain increases during 

normal operation, causing the chain to stretch. Check 
the chain tension frequently and adjust as required. A 
chain that is tensioned while warm may be too tight 
upon cooling. Make sure that the chain tension is 
correctly adjusted as specified in these instructions.

6.  Hold up the tip of the guide bar, and securely tighten the 

bar mounting nuts.

7.  Add chain lubricating oil.

Use only RYOBI chainsaw lubricating oil from an 
authorised service centre.
Clear the surface around the oil cap to prevent 
contamination. Remove the cap from the oil tank. Pour 
the oil into the oil tank, and monitor the oil level gauge. 
Ensure that no dirt enters the oil tank while filling. Close 
the oil tank, and tighten the cap. Wipe off any spillage.

WARNING!

 Never work without chain lubricant. If 

the saw chain is running without lubricant, the guide 
bar and the saw chain can be damaged. Before and 
while using the chainsaw, check the oil level in the oil 
level gauge.

8.  Ensure that the lubricant flow screw is set to open for 

the chain and bar oil to be released.

–

Turn the screw counterclockwise to open and 
increase the oil flow to the chain and bar.

–

Turn the screw clockwise to decrease the oil flow to 
the chain and bar.

A properly functioning chain and bar lubricating system 
normally discharges oil from the chain during use. To 
check the functionality of the chain and bar lubricating 
system, point the tip of the chain at a light-coloured 
surface, such as a newspaper. A distinct line of oil 
splatter should be observed after a short time.

9.  Install the battery pack.

Align the raised ribs on the battery pack with the 
grooves in the product’s battery port. Insert the battery 
pack into the product. Make sure that the latch of the 
battery pack snaps in place and that the battery pack 
is fully seated and securely attached before beginning 
operation.

WARNING!

 Always hold the product with the right hand 

on the rear handle and the left hand on the front handle.

WARNING!

 Grip both handles with the thumbs and 

fi

 ngers encircling the handles. Ensure that the left hand is 

holding the front handle so that the thumb is underneath.
10. Start the product.

Set the chain brake into the run position by grasping 
the top of the chain brake lever and pulling towards 
the front handle until you hear a click. Pull the trigger 
release. Press the switch trigger.

NOTE:

 To stop the product, engage the chain brake by 

rotating the left hand around the front handle. Allow the 
back of the hand to push the chain brake lever towards the 
bar while the chain is rotating rapidly. Release the switch 
trigger and the trigger release.

10

| English