DEFORT DPC-1316 93728663 - Инструкция по эксплуатации - Страница 17

16

LONG-TERM STORAGE

Empty the fuel/oil tanks in a well ventilated area. Store 
the fuel in approved cans in a safe place. Fit the bar 
guard. Clean the machine.

STARTING AND STOPPING

WARNING! Note the following before start-
ing: The chain brake must be engaged when 
the chain saw is started to reduce the chance 

of contact with the moving chain during starting.
Never start a chain saw unless the bar, chain and all 
covers are 

fi

 tted correctly. Otherwise the clutch can 

come loose and cause personal injuries. Place the ma-
chine on 

fi

 rm ground. Make sure you have a secure 

footing and that the chain cannot touch anything.
Keep people and animals well away from the working 
area.

COLD ENGINE

Starting: The chain brake must be engaged when the 
chain saw is started. Activate the brake by moving the 
front hand guard forwards.
1. Air purge: Press the air purge repeatedly until fuel 

begins to 

fi

 ll the bulb. The bulb need not be com-

pletely 

fi

 lled.

2.  Choke: Pull the blue choke/fast idle lever out to the 

full extent (to the FULL CHOKE position). When the 
choke/ fast idle lever is pulled out to the full extent, 
the correct throttle setting is set automatically.

  Start throttle: The correct choke/start throttle setting 

is obtained by moving the control to the choke posi-
tion.

Starting

Grip the front handle with your left hand. Hold the chain 
saw on the ground by placing your right foot through 
the rear handle.
3. Pull the starter handle with your right hand and pull 

out the starter cord slowly until you feel a resistance 
(as the starter pawls engage) then pull 

fi

 rmly  and 

rapidly. Never twist the starter cord around your 
hand.

CAUTION! Do not pull the starter cord all the 
way out and do not let go of the starter handle 
when the cord is fully extended. This can 

damage the machine.

4. Push in the choke control to the ”1/2 choke” set-

ting as soon as the engine 

fi

 res which can be heard 

through a "puff" sound.

5.  Keep on pulling the cord powerfully until the engine 

starts. Allow engine to warm for thirty seconds, then 
squeeze throttle trigger to set normal idle.

  As the chain brake is still engaged the speed of the 

engine must be set to idling as soon as possible, this 
is achieved by quickly pressing the throttle trigger 
once. This prevents unnecessary wear to the clutch, 
clutch drum and brake band.

Clean the area around the fuel cap. Clean the fuel 
and chain oil tanks regularly. The fuel 

fi

 lter must be re-

placed at least once a year. Contamination in the tanks 
causes malfunction.
Make sure the fuel is well mixed by shaking the con-
tainer before refuelling. The capacities of the chain oil 
tank and fuel tank are carefully matched. You should 
therefore always 

fi

 ll the chain oil tank and fuel tank at 

the same time.

WARNING! Fuel and fuel vapour are highly 

fl

 ammable. Take care when handling fuel and 

chain oil. Be aware of the risks of 

fi

 re, explo-

sion and those associated with inhalation.

FUEL SAFETY

•  Never refuel the machine while the engine is run-

ning.

•  Make sure there is plenty of ventilation when refuel-

ling or mixing fuel (petrol and 2-stroke oil).

•  Move the machine at least 3 m from the refuelling 

point before starting it.

•  Never start the machine:

1  If you have spilt fuel or chain oil on the machine. 

Wipe off the spillage and allow remaining fuel to 
evaporate.

2  If you have spilt fuel on yourself or your clothes, 

change your clothes. Wash any part of your body that 
has come in contact with fuel. Use soap and water.

3  If the machine is leaking fuel. Check regularly for 

leaks from the fuel cap and fuel lines.

WARNING! Never use a machine with visible 
damage to the spark plug guard and ignition 
cable. A risk of sparking arises, which can 

cause a 

fi

 re.

TRANSPORT AND STORAGE

•  Always store the chain saw and fuel so that there 

is no risk of leakages or fumes coming into contact 
with sparks or naked 

fl

 ames from electrical equip-

ment, electric motors, relays/switches, boilers and 
the like.

•  Always store fuel in an approved container designed 

for that purpose.

•  For longer periods of storage or for transport of the 

chain saw, the fuel and chain oil tanks should be 
emptied. Ask where you can dispose of waste fuel 
and chain oil at your local petrol station.

•  Ensure the machine is cleaned and that a complete 

service is carried out before long-term storage.

•  The bar guard must always be 

fi

 tted to the cutting 

attachment when the machine is being transported 
or in storage, in order to prevent accident contact 
with the sharp chain. Even a non-moving chain can 
cause serious cuts to yourself or persons you bump 
into with an exposed chain.

•  Secure the machine during transport.