Gorenje DFG 602 ORA S - Инструкция по эксплуатации - Страница 9

9 

spacers Z on the sides of the hood. 

- 

Fix the hood to the cupboard using four screws 

N

. 

Fig. 8 

Additional instructions for the montage 

Box adjustement 

The hood can be installed in cabinets with different depths, 
the front of the box must always be in line with the cabinet. 
For alignment adjust the back stops of the box. For box 
adjustment, loosen screws “

M

” and slide square plates “

G

” as 

necessary and tighten screws “

M

”. 

Fig. 9 

Description of the hood 

Fig. 1.1 
1. 

Light Switch 

2. 

Motor Speed Switch 

3. 

Illumination of the cooking surface 

4. 

Grease Filters/grease filter support grate 

5.

  Light Cover Supports  

6.

 Pull-Out 

Drawer 

Model with Grease Filter Support Grate 

Opening the Grease Filter Support Grates

 - Fig. 2.1 

a.

  Remove the pull-out drawer completely. 

b.

 Push 

the 

A

 knobs inwards toward each other (in the 

“Open” direction as indicated on the plastic knob itself). 

c.

  To remove the grates completely, use the 

B

 spring 

fasteners, which act as pins to hold the grate in place 
(Fig. 3). 

Model with Self-supporting Metal Filters 

Removing the Grease Filters

 - Fig. 2.2 

a.

  Remove the pull-out drawer completely. 

b. 

Press the side handles 

C

 (some models are supplied with 

handles Z - Fig. 2.3) towards the opposite side and 
remove the filters. 

Putting the Filters Back in Place

a.

  Remove the pull-out drawer completely and mount the 

grease filter so that it covers the drawer. 

b.

  Close the drawer and install the remaining grease filter. 

Opening the Light Cover Support

a.

  Remove the pull-out drawer completely. 

b.

   According to model in possession: 

 Lamp 

D

 with hook locks type 

A

 - Fig.2.2 

Move the bracket hook locks towards each other  (in 
direction “Open” as printed on the plastic part of the lock). 
Lamp 

F

 with hook locks type 

S

 - Fig. 1.2 

Move the hook locks as indicated by the arrows and 
completely remove the lamp from the housing (Fig. 1.3). 

Operation 

The hood is fitted with a control panel with aspiration speed 
selection control and a light switch to control cooking area 
lights. 
Use the high suction speed in cases of concentrated kitchen 
vapours.  It is recommended that the cooker hood suction is 
switched on for 5 minutes prior to cooking and to leave in 
operation during cooking and for another 15 minutes 

approximately after terminating cooking.  

Maintenance 

Before performing any maintenance operation, isolate the 
hood from the electrical supply by switching off at the 
connector and removing the connector fuse.  
Or if the appliance has been connected through a plug and 
socket, then the plug must be removed from the socket. 

Cleaning 

The cooker hood should be cleaned regularly (at least with the 
same frequency with which you carry out maintenance of the 
fat filters) internally and externally.  Clean using the cloth 
dampened with neutral liquid detergent. Do not use abrasive 
products.  

DO NOT USE ALCOHOL!

Grease filter 

Traps cooking grease particles. 

If situated inside the support grill, it may be one of the 
following types:  

Paper filter 

 must be replaced once a month or if colouring 

appears on upper side, in such cases the colouring is evident 
through the grill openings.  

Sponge filter  

should be washed with hot soapy water once a 

month and replaced every 5 to 6 washes.  

Metallic filter 

must be cleaned once a month, with non 

abrasive detergents,  by hand or in dishwasher on low 
temperature and short cycle.   
When washed in a dishwasher, the grease filter may discolour 
slightly, but this does not affect its filtering capacity. 

Removing the Grease Filters (for models wtih grease filter 
support grates)

To remove the dirty grease filter, proceed as follows: 

a.

  Remove the pull-out drawer completely and open the 

ventilation grates that support the grease filters. 

b.

 Remove 

the 

Q

 fasteners for the grease filter and remove 

it (Fig. 10.1). If special metal filters have been installed, 
press on the plastic springs 

R

  to unhook them (Fig. 

10.2). 

c.

  When washing or replacing the grease filter, wash the 

grate as well with warm soapy water.  

d.

  Remount the new filter or the old one after it has dried 

thoroughly. 

Charcoal filter (filter version only) 

It absorbs unpleasant odours caused by cooking. 
The saturation of the activated charcoal occurs after more or 
less prolonged use, depending on the type of cooking and the 
regularity of cleaning of the grease filter. 
In any case it is necessary to replace the cartridge at least 
every four mounths (or when the filter saturation indication 
system – if envisaged on the model in possession – indicates 
this necessity). 
To fit or replace a carbon filter: 

a.

  Request a charcoal filter from the retailer, specifying the 

model and type of hood. 

Caution! Some charcoal filters come covered with a plastic