Falmec Spazio 130 - Инструкция по эксплуатации - Страница 20

20

 USING THE RADIO CONTROL

WARNINGS!:

Place the hood away from sources of electromagnetic 
waves (e.g. microwave ovens), which could interfere with 

the radio control and with the hood electronics.
The maximum operating distance is 5 metres, that may vary ac-
cording to the presence of electromagnetic interferences. 
Radio control operated at 433.92MHz.
The radio control consists of two parts:
- the receiver built into the hood;
- the transmitter shown here in the figure.

DESCRIPTION OF TRANSMITTING COMMANDS

UP

Motor switch-on and speed in-
crease from 1 to 4. Speed 4 is only 
active for a few minutes.

DOWN

Speed decrease and motor 
switch-off.

Light ON-OFF

TIMER ON: 

The motor automati-

cally switches off after 15 min.
The function is automatically dis-
abled if the motor is switched off 
(

 key)

Command transmission active

RADIO CONTROL CODE CHANGE

With only one radio control, go directly to point 2.
With several radio controls in the same room, a new code can be creat-
ed by following the procedure below.

Disconnect the power to the hood before starting the pro-
cedure.

1) - CREATE A NEW CODE

The procedure is to be carried out on the radio control.

•

 Press LIGHT 

 and TIMER 

 simultaneously until the display starts 

flashing.

•

 Press DOWN 

 on the radio control: saving is confirmed by three 

brief flashes of the display. The new code cancels and replaces the 
previous default code. 

Reconnect the hood to the electrical power supply, making 
sure that the lights and motor are off. 

2) - ASSOCIATING THE RADIO CONTROL WITH THE HOOD
           USING THE ELECTRONIC PUSHBUT TON PANEL
 

press TIMER (

) 

on the hood pushbutton panel

 for 2 seconds:

the red LED lights up. 
press any key on the radio control within 10 seconds. 

RESTORING DEFAULT CODE

the procedure is to be carried out if the hood is disposed of, sold or 
transferred.

Disconnect the power to the hood before starting the pro-
cedure.

•

 Press UP 

 and DOWN 

 simultaneously on the radio control for 

more than 5 seconds: reset is confirmed by three brief flashes of the 
display. 

•

  Reconnect the hood to the electrical power supply.

•

  Proceed with associating the hood and the radio control, as de-

scribed in point 2.

 MAINTENANCE

Before cleaning or carrying out maintenance operations, 
disconnect the equipment by removing the plug or 
switching off the main switch.

Do not use detergents containing abrasive, acidic or corrosive 
substances or abrasive cloths.

Regular maintenance guarantees proper operation and performance 
over time.
Special attention is to be paid to the 

metal anti-grease filters 

: fre-

quent cleaning of the filters and their supports ensures that no flamma-
ble grease is accumulated.

CLEANING OF EXTERNAL SURFACES

You are advised to clean the external surfaces of the hood 

at least once 

every 15 days

to prevent oily substances and grease from sticking to 

them. To clean the brushed stainless steel hood, the Manufacturer rec-
ommends using "Magic Steel" wipes.
Alternatively 

and for all the other types of surfaces

, it can be cleaned 

using a damp cloth, slightly moistened with mild, liquid detergent or 
denatured alcohol.
Complete cleaning by rinsing well and drying with soft cloths. 

Do not use too much moisture or water around the push 
button control panel and lighting devices in order to pre-
vent humidity from reaching electronic parts.

The glass panels can only be cleaned with specific, non-corrosive or 
non-abrasive detergents using a soft cloth.
The Manufacturer declines all responsibility for failure to comply with 
these instructions.

CLEANING OF INTERNAL SURFACES

Do not clean electrical parts, or parts related to the motor 
inside the hood, with liquids or solvents.

For the internal metal parts, see the previous paragraph.