Falmec Nube 90 inox - Инструкция по эксплуатации - Страница 30

30

plus button

Press this key with the motor of (no symbol on the display) to switch the hood 
on with speed 1.
If the motor is running, pressing this key increases the motor speed.
Speed 1, 2, 3, and 4 are displayed on the screen by their equivalent symbol 

number 

. The 4th speed or intensive setting is timed and after about 7 

minutes the motor automatically switches to the 3rd speed. 

minus button

Press this key with the motor of (no symbol on the display) to switch the hood 
motor on with speed 1 (minimum).
If the motor is running, pressing this key decreases the motor speed.
Speed 1, 2, 3, and 4 are displayed on the screen by their equivalent symbol 

number 

. 

If the motor is running at speed 1, pressing the key switches the hood motor 
of.

timer

Pressing the key with the motor active at any speed switches the 

timer

 func-

tion on and of: this function determines the 

auto switch-of of the hood 

after 15 minutes of operation.

 Activation of this function is signalled by the 

symbol 

 (Hourglass) on the display. With the Timer function active, the 

hood can still be switched of by the user at any time by reducing the speed 

with the 

  key until the motor switches of: the function will be auto-

matically disabled and the symbol 

(Hourglass) will disappear from the 

display.

operAtion

when ShoUlD the hooD be SwitcheD on AnD off?

Switch on the hood at least one minute before starting to cook: this enhances the airlow 
to convey fumes and vapours towards the suction surface. After cooking, leave the hood 
operating until complete extraction of all vapours and odours. If required, for versions with 
electronic push button control panel, by means of the Timer function, it is possible to set 
hood auto switch-of after 15 minutes of operation.

which SpeeD iS to be SelecteD?

The 

irst

 speed is a low consumption energy-saving way of keeping the air clean, the 

sec-

ond

 speed is used in normal conditions, and the 

third

 speed is used when there are strong 

odours and vapours. 

when ShoUlD the filterS be wASheD or replAceD?

The hood has metal ilters (washable), which must be cleaned after approximately 30 hours 
of use. 
For further information, please read the chapter regarding ''

maintenance''

 on page 

31

. 

wArningS when USing the rADio control

The Nube hood is, by default, equipped with a 4-channel radio control.
Place the hood away from sources of electromagnetic waves (e.g. microwave ovens), which 
could interfere with the radio control and, consequently, with the hood electronics. The max-
imum operating distance is 5 metres; the distance may vary according to the presence of 
electromagnetic interference from other devices.

radio control operated at 433.92mhz.

rADio control coDe chAnge 

(to be USeD only in cASe of 

mAlfUnction DUe to interference)

A  default transmission code is factory installed and stored, which is required to transmit 
controls from the radio control to the hood. 
Should electromagnetic interference with other devices cause a radio control malfunction, 
a new transmission code can be created by following the procedure indicated in points 

1

and 

2

.

1

 creAting A new trAnSmiSSion coDe

• 

Disconnect the hood from the electrical mains power supply by unplugging it or by 
turning of the main switch.

• 

To access the "code change" mode, simultaneously press the 

 (light) and 

(timer) keys on the radio control until the display starts lashing slowly (approximately 
4/5 seconds).

• 

If, within 5 seconds from when the display starts lashing the radio control 

 (minus) 

key is pressed, a random transmission code is created and saved: saving is conirmed by 
three brief lashes of the display. The new code cancels and replaces the previous factory 
default transmission code. 

• 

Reconnect the hood to the electric power supply, making sure that the lights and motor 
are of.

2

 ASSociAting the rADio control with the hooD

To save the new transmission code created in the hood, press the 

 (timer) key on the 

push-button control panel of the hood for 2 seconds and, after the corresponding red LED 
has lit up on the push-button control panel, press any key on the radio control within 10 
seconds. 

reStore the DefAUlt coDe (fActory DefAUlt coDe)

• 

Should it be necessary to restore the default transmission code, disconnect the hood 

from electric power supply and simultaneously press the 

 (minus) and 

 (plus) 

keys on the radio control for more than 5 seconds. This restores the radio control default 
transmission code factory setting: three brief lashes on the display are issued as a con-
irmation that it has been saved.

• 

Proceed with associating the hood and radio control, as described in point 

2

.

• 

 Connect the hood to the electric power supply.

USing the rADio control