DeLonghi KD-LA60 - Инструкция по эксплуатации - Страница 11

- 11 -

ENGLISH

GB

 GENERAL

Carefully read the following important information regarding 

installation safety and maintenance. Keep this information 

booklet accessible for further consultations. The appliance 

has been designed for use in the ducting version (air exhaust 

to the outside - Fig.1B), filtering version (air circulation on the 

inside - Fig.1A) or with external motor (Fig.1C).

 SAFETY PRECAUTION

1.

 Take care when the cooker hood is operating simultane-

ously with an open fireplace or burner that depend on the air 

in the environment and are supplied by other than electrical 

energy, as the cooker hood removes the air from the environ-

ment which a burner or fireplace need for combustion. The 

negative pressure in the environment must not exceed 4Pa 

(4x10-5 bar). Provide adequate ventilation in the environment 

for a safe operation of the cooker hood. Follow the local laws 

applicable for external air evacuation.

Before connecting the model to the electricity network:

- Control the data plate (positioned inside the appliance) 

to ascertain that the voltage and power correspond to the 

network and the socket is suitable. If in doubt ask a qualified 

electrician.

- If the power supply cable is damaged, it must be replaced with 

another cable or a special assembly, which may be obtained 

direct from the manufacturer or from the Technical Assistance 

Centre.

- This device must be connected to the supply network through 

either a plug fused 3A or hardwired to a 2 fase spur protected 

by 3A fuse.

2.  Warning!

In  certain  circumstances  electrical  appliances  may  be  a 

danger hazard.

A)  Do not check the status of the filters while the cooker 

hood is operating.

B)  Do not touch bulbs or adjacent areas, during or straight 

after prolonged use of the lighting installation.

C)  Flambè cooking is prohibited underneath the cooker 

hood.

D)  Avoid free flame, as it is damaging for the filters and a 

fire hazard.

E)  Constantly  check  food  frying  to  avoid  that  the  over

-

heated oil may become a fire hazard.

F)  Disconnect the electrical plug prior to any maintenance.

G)  This appliance is not intended for use by young children 

or infirm persons without supervision.

H) Young children should be supervised to ensure they do 

not play with the appliance.

I)   There shall be adequate ventilation of the room when 

the rangehood is used at the same time as appliances 

burning gas or other fuels.

L)  There is a risk of fire if cleaning is not carried out in 

accordance with the instructions.

This appliance conforms to the European Directive EC/2002/96, 

Waste Electrical and Electronic Equipment (WEEE). By making 

sure that this appliance is disposed of in a suitable manner, the 

user is helping to prevent potential damage to the environ-

ment or to public health.

The symbol on the product or on the accompanying 

paperwork indicates that the appliance should not be 

treated as domestic waste, but should be delivered to 

a suitable electric and electronic appliance recycling collection 

point. Follow local guidelines when disposing of waste. For 

more information on the treatment, re-use and recycling of 

this product, please contact your local authority, domestic 

waste collection service or the shop where the appliance was 

purchased.

 INSTALLATION INSTRUCTIONS

•  Assembly and electrical connections must be carried out 

by specialised personnel.

•  Wear protective gloves before proceeding with the instal

-

lation.

•  Electric Connection:

- The appliance has been manufactured as a class II, therefore 

no earth cable is necessary. The plug must be easily acces-

sible after the installation of the appliance. If the appliance 

is equipped with power cord without plug, a suitably di-

mensioned omnipolar switch with 3 mm minimum opening 

between contacts must be fitted between the appliance and 

the electricity supply in compliance with the load and current 

regulations.

- The connection to the mains is carried out as follows:

BROWN = 

L

 line

BLUE = 

N

 neutral.

•  

If the hob is electric, gas, or induction, the minimum distance 

between the same and the lower part of the hood must be at 

least 

65 cm

. If a connection tube composed of two parts is 

used, the upper part must be placed outside the lower part. Do 

not connect the cooker hood exhaust to the same conductor 

used to circulate hot air or for evacuating fumes from other 

appliances generated by other than an electrical source.

-  In the case of assembly of the appliance in the suction version 

prepare the hole for evacuation of the air.

•  

We recommend the use of an air exhaust tube which has the 

same diameter as the air exhaust outlet hole. If a pipe with a 

smaller diameter is used, the efficiency of the product may be 

reduced and its operation may become noisier.

•  

If your appliance has been designed for use in habitations 

supplied with acentralised suction device perform the follow-

ing operations:

- The switch controls opening and closure of a valve using 

a thermoelectical device. By placing the switch in the 

ON 

position, after a minute, the valve opens rotating 90° allow-

ing suction of the stale air. By placing the switch in the

 OFF

position, the valve closes after 100 seconds.

•  Warning: 

if the bulbs are not working, ensure that they are 

screwed in fully.

•  Installation:

Prior to proceeding with the assembly operations (according 

to the model that you have purchased), to facilitate handling 

of the device, remove the grille as indicated in figure 6 or the 

aluminium panels as indicated in figure 7.

•  

The appliance is equipped with 2 air outlets, to be used in 

accordance with your specific requirements: one is located 

on the upper part of the appliance and the other at the rear 

(Fig.1A).

The flange 

D

, to which the air exhaust pipe is connected, and 

a plug 

B

, used to shut off the unused air outlet, are both sup-

plied with the product.

•  

This device may be installed in two different ways:

1. Fixing  the  hood  to  the  lower  part  of  the  wall  cabinet 

(Fig.2):

- Make 4 holes in the wall cabinet respecting the measurements 

indicated in figures 2A-2C.

- Position the hood underneath the wall cabinet and fix it into 

place using 4 screws (not supplied) suitable for the type of 

cabinet.