De Dietrich DHT1146X - Инструкция по эксплуатации - Страница 40

40 

Fig. 8.1 - 8.2 - 8.3 

Warning!

  The cooker hood is supplied with 4 side 

spacers (2 for the right side and 2 for the left side), these 
are useful when the width of the housing cabinet for the 

cooker hood motor body is wider than 6mm.  
In this instance the spacers should be mounted outside 
the cooker hood body corresponding to the perforations for 

the cabinet fixing screws. 

 Z

 - 

Fig. 8.1-8.3

  
The hood must be fitted with a pipe having the same diameter 
as the air outlet. 
  
To mount the hood proceed as follows: 
- 

Position the drilling template inside the left cupboard on 
the right hand side with the arrow point towards the back 
on the cupboard. 

- 

Drill the holes marked on the template. 

- 

Repeat the procedure for the right hand cupboard 

- 

If the sides of the cupboards are 16 mm thick, insert 4 
spacers 

Z

 on the sides of the hood. 

- 

Fix the hood to the cupboard using four screws 

N

. 

Fig. 8.3 

Additional instructions for the montage 

Box adjustement 

The hood can be installed in cabinets with different depths, 
the front of the box must always be in line with the cabinet. 
For alignment adjust the back stops of the box. For box 
adjustment, loosen screws “

M

” and slide square plates “

G

” as 

necessary and tighten screws “

M

”. 

Fig. 9 

Operation 

The hood is fitted with a control panel with aspiration speed 
selection control and a light switch to control cooking area 
lights. 
Use the high suction speed in cases of concentrated kitchen 
vapours.  It is recommended that the cooker hood suction is 
switched on for 5 minutes prior to cooking and to leave in 
operation during cooking and for another 15 minutes 
approximately after terminating cooking.  

Maintenance 

ATTENTION! 

Before performing any maintenance operation, 

isolate the hood from the electrical supply by switching off at 
the connector and removing the connector fuse.  
Or if the appliance has been connected through a plug and 
socket, then the plug must be removed from the socket. 

Cleaning 

The cooker hood should be cleaned regularly (at least with the 
same frequency with which you carry out maintenance of the 
fat filters) internally and externally.  Clean using the cloth 
dampened with neutral liquid detergent. Do not use abrasive 
products. 

DO NOT USE ALCOHOL!

WARNING: 

Failure to carry out the basic cleaning 

recommendations of the cooker hood and replacement of the 
filters may cause fire risks.  

Therefore, we recommend observing these instructions. 
The manufacturer declines all responsibility for any damage to 
the motor or any fire damage linked to inappropriate 
maintenance or failure to observe the above safety 
recommendations. 

Grease filter 

Traps cooking grease particles. 

If situated inside the support grill, it may be one of the 
following types:  

Paper filter 

 must be replaced once a month or if colouring 

appears on upper side, in such cases the colouring is evident 
through the grill openings.  

Metallic filter 

must be cleaned once a month, with non 

abrasive detergents,  by hand or in dishwasher on low 
temperature and short cycle.   
When washed in a dishwasher, the grease filter may discolour 
slightly, but this does not affect its filtering capacity. 

Removing the Grease Filters (for models wtih grease filter 
support grates)

To remove the dirty grease filter, proceed as follows: 

a.

  Remove the pull-out drawer completely and open the 

ventilation grates that support the grease filters. 

b.

 Remove 

the 

Q

 fasteners for the grease filter and remove 

it (Fig. 10.1). If special metal filters have been installed, 
press on the plastic springs 

R

  to unhook them (Fig. 

10.2). 

c.

  When washing or replacing the grease filter, wash the 

grate as well with warm soapy water.  

d.

  Remount the new filter or the old one after it has dried 

thoroughly. 

Charcoal filter (filter version only) 

It absorbs unpleasant odours caused by cooking. 

The saturation of the charcoal filter occurs after more or less 
prolonged use, depending on the type of cooking and the 
regularity of cleaning of the grease filter. In any case it is 
necessary to replace the cartridge at least every four mounths 
(or when the filter saturation indication system – if envisaged 
on the model in possession – indicates this necessity).The 
charcoal filter may NOT be washed or regenerated. 
To fit or replace a carbon filter: 

a.

  Request a charcoal filter from the retailer, specifying the 

model and type of hood. 

Caution! Some charcoal filters come covered with a plastic 
film to protect their filtering properties. If this is the case, 
remove the film before installing the filter.

b.

  Remove the pull-out drawer completely. 

c.

  Remove the grease filters or the grates. 

d.  

Place the activated carbon filter in position: 
1)   Version with one motor: insert the filter in its housing 

over the plastic grill and rotate it until it locks in 
position (Fig. 6). 

2)   Version with two motors: to assemble the filter, 

insert it in its seating and fix it in position using the 
clips 

L

 (Fig. 7) 

e.

  Remove the grease filters or grills 

To remove the carbon filter, follow the procedure described in 
item 1) or 2), depending on the version) in the reverse order.