AEG DDLE Basis 18 / 21 / 24 / 27 - Инструкция по эксплуатации - Страница 30

30

฀

Alternative฀installation฀methods฀are฀shown฀in฀igures

J

฀-

O

.

4.1 

Power supply – unfinished walls - below

K

a

  Push the cable grommet (4) over the power cable.

b

  Break out the cable grommet knock-out in the back panel.

c

฀ Move฀the฀terminal฀strip฀from฀the฀top฀to฀the฀bottom;฀for฀this,฀undo฀the฀screw฀and฀reit฀it฀into฀the฀terminal฀

strip moved to the bottom.

d

  Slide the back panel over the studs and the cable grommet, pull the cable grommet with a pair of pliers 

against the locking hooks and let both hooks audibly click into place.

e

฀ Push฀the฀back฀panel฀irmly฀and฀lush฀against฀the฀wall฀and฀lock฀with฀the฀ixing฀toggle฀(11).

4.2 

Power supply – finished walls

•฀ Cut/break฀a฀hole฀into฀the฀back฀panel฀suitable฀for฀the฀power฀cable฀(for฀possible฀knock-outs฀see

J

 ).

•฀ With฀power฀supply฀on฀inished฀walls,฀the฀protection฀rating฀is฀reduced฀to฀IP฀24฀(splash-proof).

฀ Please฀note:฀

Mark the type plate with a permanent marker: 
Cross out IP 25 and tick the IP 24 box.

4.3 

Priority control

L

When฀used฀in฀conjunction฀with฀other฀electrical฀equipment,฀e.g.฀electric฀storage฀heaters,฀use฀the฀maximum฀

demand relay:

a

  Maximum demand relay (see “8. Special accessories”).

b

  Control cable to the contactor of the second device (e.g. electric storage heater).

c

  Control contact, opens when switching the instantaneous water heater on.

฀ The฀relay฀trips฀as฀soon฀as฀the฀instantaneous฀water฀heater฀starts.

Only฀connect฀the฀automatic฀maximum฀demand฀controller฀to฀the฀central฀phase฀of฀the฀equipment฀terminals฀

(mains฀power).

4.4 

Undersink installation, water connections from the top

Undersink installation with water connections from the top can be achieved with the additional pipe assembly 
for undersink devices (part no. 18 44 21). Cleanly break out the water pipe knock-outs in the back panel and 

it฀the฀pipe฀set.

4.5 

Temperature limit

If the maximum temperature is to be limited to 43 °C, this is done on the inside of the 
device cap. For this, replug the temperature selector cable in the device cap from 60 °C 

to฀43฀°C.฀You฀can฀still฀adjust฀the฀temperature฀selector฀across฀its฀entire฀range.฀The฀outlet฀

temperature will be permanently limited to 43 °C. A temperature range 30 °C to 43 °C 
can be selected.

4.6 

Taps for finished walls

AEG-Haustechnik฀-฀pressure฀tested฀tap฀for฀inished฀walls฀
ADEo฀70฀WD

N

฀

(part no. 18 39 34):

•฀ Fit฀plug฀G฀½"฀with฀gaskets฀(a)฀

(part of the standard delivery of the pressure tested tap ADEo 70 WD).

•฀ Fit฀the฀tap.
•฀ Insert฀the฀support฀plate฀into฀the฀lower฀part฀of฀the฀back฀panel.฀The฀support฀plate฀is฀part฀of฀the฀standard฀

delivery of the tap and is designed to hold the tap pipes in the designated location as well as to ensure 
the necessary protection against moisture ( 

M

 31).

•฀

Push the tap pipes from above through the support plate up to the lower part of the back panel.

•฀ Push฀the฀open฀end฀of฀the฀pipes฀into฀the฀valve.
•฀ Click฀the฀lower฀part฀of฀the฀back฀panel฀together฀with฀the฀support฀panel฀and฀the฀pipes฀into฀the฀upper฀part฀

of the back panel.

•฀ Secure฀the฀connection฀pipes฀on฀the฀device.

The฀device฀cap฀needs฀to฀the฀prepared฀tor฀this฀installation:฀

Cleanly break out the knock-outs in the device cap ( 

M

฀a),฀use฀a฀ile,฀if฀necessary.

Device฀ixing:฀

Secure the back panel in the lower part of the device with two additional screws ( 

M

 24).

60°C

43°C

For contractors

4. 

Alternative installation methods

 for contractors 

Power supply: unfinished walls - below, maximum demand relay; undersink installation, water  

connections - top; water: finished walls