Vestel VHI64371B - Инструкция по эксплуатации - Страница 36

EN - 15

be displayed and the hob will switch off.

Key Lock

The key lock function is used to set 

‘safe mode’ on the appliance during 

operation. It will not be possible to make 

any adjustments by pressing the buttons 

(for example heat settings). It will only be 

possible to switch the appliance off.

The lock function is active if the key lock 

button   is pressed for at least 2 seconds. 

This operation is acknowledged by a 

buzzer. After successful operation, the key 

lock indicator will flash and the heater will 

be locked.

Timer Function

The timer function is available in two 

versions, as follow.

Minute Minder Timer (1 - 99 min.)

The minute minder timer can be operated 

if the cooking zones are switched off. The 

timer display will show “

00

” with a blinking 

dot.

Use the Timer   and Sliding Button 

 to increase/decrease the time. 

The range is between 0 and 99 minutes. 

If there is no adjustment to the displayed 

time within 10 seconds, the minute minder 

timer will be set and the blinking dot will 

disappear. Once the timer is set, it begins to 

count down.

When the timer reaches zero, a signal will 

sound and the timer display will blink. The 

sound signal will stop automatically after 2 

minutes and/or by pressing any button.

The minute minder timer can be changed or 

switched off any time by using the Timer   

and Sliding Button 

. Switching off 

the hob by touching   at any time will also 

switch off the minute minder timer.

Cooking Zone Timer (1 - 99 min.)

When the hob is switched on, an 

independent timer can be programmed for 

each cooking zone.

Select a cooking zone, then select the 

temperature setting and, finally, activate the 

timer setting button   , the timer can be 

programmed to switch off a cooking zone. 

Four LEDs are arranged around the timer 

that indicate which cooking zone the timer 

has been set for.

10 seconds after the last operation, the 

timer display will change to the timer that 

will run out next (in cases where a timer is 

set for more than one cooking zone).

When the timer has run down, a signal will 

sound, the timer display will show “

00

” and 

the assigned cooking zone timer LED will 

blink. The programmed cooking zone will 

switch off and “

H

” will be displayed if the 

cooking zone is hot.

The sound signal and the blinking of the 

timer LED will stop automatically after 2 

minutes and/or by pressing any button.

Buzzer

While the hob is in operation, the following 

activities will be signalled by the buzzer.

•  Normal button activation will be 

accompanied with a short sound signal.

•  Continuous button operation over a 

longer period of time (10 seconds) 

will be accompanied with a longer, 

intermittent sound signal.

Boost Function

To use this function, select a cooking zone 

and set the desired cooking level, then 

press the “

P

” (Boost) button.

The Boost function can only be activated 

if it is applicable with the cooking zone 

selected. If the Boost Function is active, 

a “

P

” will be shown on the corresponding 

display.

Activating the booster can exceed the 

maximum power, in which case the 

integrated power management will be 

activated.

The necessary power reduction is shown 

by the corresponding cooking zone display 

blinking. Blinking will be active for 3 

seconds to allow for further adaptations of 

the settings before power reduction.

Bridge Zone

Switching the Bridge Zone On

Touch the front left and rear left heater 

selection buttons simultaneously. A static 

dot will be shown on the left heater display. 

The other displays will show ‘

b

’ and ‘

r

’, the 

blinking dots will no longer be displayed.

Select the temperature setting by using the 

sliding button. Increase the heat setting by 

pressing the right side of the sliding button 

or decrease the heat setting by pressing the 

left side of the sliding button.

The bridge element will be ready to use. 

For the fastest boil time, select the desired 

cooking level, then press the “

P

” key to 

activate the Boost function.

Switching the Bridge Zone off

To select the Bridge element, press the rear 

left or front left heater selection button and,