Fulgor Milano CPH 402 ID TC X/2 - Инструкция по эксплуатации - Страница 15

14

15

GB

Timer function

The Timer function can be used as a 
cooking zone timer or independent alarm 
but never for both functions. The two 7 

segment displays of the respective cooking zones are used 
to view the remaining time in minutes up until the timer 
alarm is activated. 

Timer selection

- To program a timer, the touch control must be in the 

Standby or On mode. 

-  The timer button is pressed in order to select a timer 

function for the cooking zone. 

-  The programming of a timer using the Plus/Minus keys 

is signalled by led 8 for induction model 2 and led 6 for 
the wok induction model. The flashing timer LED signals 
that the 7 segment display value refers to the timer and 
can be modified. When a timer continues to function in 
the OFF mode, the timer LED remains on. 

  This indicates that the value on the display is related to 

the timer, but cannot be directly modified at that particular 
moment; to do so, the control must be reactivated. 

- The activation of the timer button depends on the 

conditions of the previously set function: a) The cooking 
zone corresponding to the timer is on (cooking level > 
0): The timer is programmed in reference to the cooking 
zone; the cooking zone automatically switches off when 
reset; an independent timer cannot be selected. The 
cooking level setting is accessed when the timer button 
is pressed again. 

  b) The cooking zone corresponding to the timer is 

off (cooking level = 0): The timer is independently 
programmed and continues to function even in OFF. 
The cooking zone cannot be activated until the timer is 
functioning. 

Setting of the Timer value

- Following the selection of the time, the related LED 

flashes as described above. The countdown time of the 
desired timer can be set by means of the +/- buttons. 

-  Starting with the plus button, the first value displayed is 

“01” and progressively increases from 1 to a maximum 
value of “99” (upper limit). 

-  Starting with the minus button, the value displayed on 

the indication is “30” and diminishes to “01” (first lower 
limit). When this value is reached, an acoustic signal is 
emitted. By pressing the minus button again, the display 
“00” will not be modified (second lower limit). 

-  Setting can be performed by permanently pressing the 

plus or minus buttons or by intermittently pressing them 

(selection: press button, release, press button, release, 
etc). 

- If the button is permanently pressed, the regulation 

speed automatically accelerates, meaning that the time 
between one step and the next is reduced, until the 
button is released. 

-  If the Plus or Minus buttons are not pressed within 10 

sec. (parameter), after having selected the timer of the 
current cooking zone (the display remains on “00”), the 
indication and allocation of the +/- buttons automatically 
switch to the cooking zone. 

-  When a timer is used as an alarm, the indication and 

allocation of the buttons does not switch to the cooking 
zone, being that this cannot be activated.

-  The timer normally starts in countdown, if programmed 

with two values that are not 0. For example: the timer 
starts when the Plus button is released after the timer 
value has been set at “01”. 

-  The timer settings have priority over the delimitation of 

the operating time if high cooking levels have been set. 

- If only one alarm has been programmed, the control 

remains at first in the standby mode (no other cooking 
zone is on). If no other new values are introduced, the 
TC behaves as described above and switches to the 
OFF mode.  

Timer laps/ timer alarm and confirmation

-  The last 10 sec. before the timer lapses are displayed 

(countdown up to alarm).

-  Once the set time of the timer has lapsed, the timer alarm 

is activated and the assigned cooking zone is switched 
off. 

-  The display and the selected timer LED flash alternating 

the cooking level from “00” to “H”, if there is residual heat. 

-  The warning alarm lasts for at least 2 minutes if the user 

does not switch it off before. 

-  The alarm signal switches off after the 2 minutes is up or 

if any button is pushed. 

  The buzzer and the timer control light are switched off. 

Timer off /Modification of the timer setting

-  The timer settings can be modified in the Standby or On 

mode at any time after the selection has been made by 
pressing the Plus or Minus buttons. 

-  The timer can be switched off, setting it to value “00”, by 

pressing the Minus button or by pressing the Plus and 
Minus buttons together.