Fulgor Milano CPH 1124 G WK X - Инструкция по эксплуатации - Страница 16

16

17

GB

Installation

All the operations concerned with the installation 
(electrical and gas connections, adaptation to type of 
gas, necessary adjustments, etc.) must be carried out 
by qualified technicians, in terms with the standards 
in force. For specific instructions, kindly read the part 
reserved for the installation technician.

Use

Standby mode (Fig. 1-2-3)

When the device is turned on, it performs a brief self-test 
and calibrates the touch-pad (all displays and LEDs turn 
on for several seconds). At the end, the display will be 
completely off. In this mode, the device can be turned on 
by simply pressing the ON/OFF key. 

Turning on the Cooking Surface

To turn on the device, you must hold down the ON/
OFF key for at least 2 seconds. The device will turn on 
and the burner displays will display level zero, which 
corresponds to burner off. 

Turning on a burner

To turn on a burner, press the relative + and - keys on the 
control panel. The keys must be pressed simultaneously 
and held down for at least 1 second. When the burner 
turns on, the burner will be set to the average flow and 
the relative display will show level 3.
Each burner whose timer has not been programmed 
will automatically turn off after 4 hours of continuous 
operation.
The turning on of the burner is also indicated by the 
relative LED near the timer display, which will be on for 
the entire time that the burner is on.

Adjusting the flame level of a burner

To increase the flow to a burner that is on, press the 
+ key and to decrease the flow, press the - key. For a 
continuous change in the flow level, just hold down the + 
or - key and release it at the desired level. The flow level 
varies form 1 to 5.

Turning off a burner

To turn a burner off, press the + and - keys simultaneously 
for a brief instant. 

Turning off all the burners

To turn all the burners off at the same time, briefly press 
the ON/OFF key; this puts the device in standby mode. 

Programming the amount of time after which the 
burner turns off

A time, after which a burner turns off, can be set 
independently for each burner.
To program a burner timer, press the PT key. In the 
part of the control panel that shows the position of each 
burner with an LED, the burner A indicator (LED-A) 
lights to indicate that burner A is currently selected for 
programming. Use the P+ and P- keys to select the timer 
of the burner to be programmed. The selected burner is 
indicated by the flashing of its light. The timer display 
shows 0.00 to indicate that the timer for the selected 
burner is not active. To program the turn-off time for 
the selected burner, press the PT key again; the timer 
display will show 0.00. The flashing digit to the left of the 
decimal point indicates hours while the digits to the right 
indicate minutes. By pressing the P+ or P- keys, you can 
increase, or decrease, the number of operating hours 
from 0 to 9. When you hold down the P+ or P- keys, the 
change of hours is continuous.
To specify the number of minutes, press PT again. The 
digit to the right of the decimal point flashes. Set the 
minutes the same way as the hours. 
When programming the time, you can zero the current 
setting at any time by pressing the P+ and P- keys 
together. When a time of zero is set, the burner timer is 
deactivated. To confirm the time displayed, press the PT 
key. At this point, the only burner LEDs that are flashing 
are those whose timers are running.
By pressing the PT key, you can return to timer 
programming mode to see how much time remains 
before the burner turns off or to change the current 
setting. If, during programming, no key is pressed for 
longer than 10 seconds, programming is automatically 
interrupted and the main display returns. Any settings 
that were made for the selected burner are stored and 
the relative timer is running.
A timer can be set whether a burner is on or off and the 
countdown starts immediately after the time setting is 
confirmed. When the countdown ends, the timed burner 
will turn off and a sequence of beeps will sound for 30 
seconds. This sequence can be interrupted by pressing 
the PT key.
When you turn off a burner, its timer is also deactivated.

Setting the clock

After a power failure, the time displayed by the clock 
inside the device must be reset.
To set the clock, you must press the PT, P+ and P- keys 
simultaneously for at least 3 seconds.
The flashing digit to the left of the decimal point indicates 
hours while the digits to the right indicate minutes. 
Pressing the P+ or P- keys increases or decreases the 
hours and, when you hold down the P+ or P- key, the 
number of hours changes continuously.
Press the PT key again to set the minutes. The digits 

Instructions for use