Bertazzoni PM36 3 I0 X - Инструкция по эксплуатации - Страница 11

11

controlled.. 
Push and turn the knob to the right to set the zone's operating power; the settings range from a minimum of 
1 to a maximum of 9. (fig.15-16) 

Heating accelerator 

Each cooking zone is equipped with a heating accelerator. 
This system allows the zone to be operated at peak power for a time proportional to the heating power 
selected. 
To start the heating accelerator, turn the knob to the left, select setting "A" and then release.  
You now have 3 seconds to select the heating setting between 1 and 9. 
While the heating accelerator is in operation, the heating level can be increased at any time. The "full power" 
time will be modified accordingly. If the power is reduced by turning the knob anticlockwise, the heating 
accelerator is automatically deactivated. 
 

Powerboost Function 

The power function allows the user to operate each heating zone continuously at the maximum power for a 
time of no more than 10 minutes. This function can be used, for example, to bring a large amount of water to 
the boil in a hurry, or to turn up the heat under meat. 
Push and turn the knob clockwise and set heating level 9, then use the knob to set the "B" position and 
release il. "B" appears on the corresponding zone display. 
After 10 minutes, the power is reduced automatically, "B" led is switched off. 
However, the power function can be turned ott at any time by reducing the heating level. . 
When the power function is selected for one heating zone, the power absorbed by the second zone  might 
be reduced to supply the maximum available energy to the first zone. 
If a pan is removed from the cooking zone while the power function is on, the function is switched off. 

Child lock 

The child lock function prevents switching on of the control unit, to avoid unwanted operation, for example by 
children, While child lock is activated, no cooking zone can be used. 
The child-lock mode is activated by overwinding the two knobs in anti-clockwise direction for mode than 1,5 
secs-alternatively: one knob for more 5 secs; AND less than 30 secs to avoid failure detection. 
The child-lock is disabled in the same way. 
Aktivation/disabling is only possible if both knob input units are in zero position. 

Type of pans 

This type of appliance can only operate with pans of special kinds. 
The bottom of the pan must be iron or steel/iron to generate the magnetic field necessary for the heating 
process 
Vessels made from the following materials are not suitable: 



 glass; 



 porcelain; 



 pottery; 



steel, aluminium or copper without magnetic bottom; 

To check that a pan is suitable, simply piece a magnet close to its bottom: 
if the magnet is attracted, the pan is suitable for induction cooking.  
The pans used for cooking must have certain minimum diameters to ensure satisfactory operation. 
Pans larger than the cooking zones can also be used, but it is important to ensure that the bottom of the 
pan does not touch other cooking zones, and that it is always centred over the perimeter of the cooking 
zone. 
Use only vessels specially designed for induction cooking, with thick, completely flat bottom; if these are not 
available, the pans used must not have crowned (concave or convex) bottom. (fig.16) 

Residual heat 

Each cooking zone is equipped with a device which warns of residual heat. After any cooking zone is 
switched off, a ‘H’ may appear on the display. This warns that the cooking zone concerned is still very hot. 
Cooking can be restarted while the ‘H’ is on. 

Attention: 

Take care not to spill sugar or sweet mixtures onto the hob during cooking, or to place materials or 
substances which might melt (plastic or aluminium foil) on it; if this should occur, to avoid damage to the 
surface, turn the heating off immediately and clean with the scraper supplied while the cooking zone is still