Ryobi RBC254SESO 5133002536 - Инструкция по эксплуатации - Страница 31

Deutsch (Übersetzung der originalen Anleitungen) 

29

English (Original instructions)

CONVERTING FROM BRUSHCUTTER TO GRASS 
TRIMMER:

(See Fig 2f)

When using the string head, the blade guard must be 
attached with the grass de

fl

 ector.

 WARNING

 To reduce the risk of serious personal injury, 

always stop the engine before making any 
adjustments such as changing cutting heads.

 WARNING

 Be certain all knobs and fasteners are fully 

t i g h t e n e d   b e f o r e   o p e r a t i n g   t h e   e q u i p m e n t . 
Periodically check for tightness during use to 
avoid serious injury.

Removing the Tri-arc™ blade

■

Stop the engine.

■

Place the Combination wrench through the hole in 
the upper flange washer and the hole in the gear 
head. Using the wrench, turn the blade retainer nut 
clockwise to remove.

■

Remove the cupped washer and blade.

■

Remove the upper flange washer from the gear shaft 
and retain for the later use.

Installing the ReelEasy™ string head

■

Install the upper flange washer onto the gear shaft with 
the hollow side towards the gear head.

■

Install the drive connector into the gear shaft. Place 
the combination wrench through the hole in the upper 
flange washer and the hole in the gear head. Using the 
wrench, turn the drive connector counterclockwise and 
tighten securely.

■

Place the string head housing on the drive connector.

■

Make sure the housing is fully seated.

■

Place the combination wrench through the hole in the 
upper flange washer and the hole in the gear head.
Place the hex bolt into the drive connector. Using the 
bump knob, to turn the hex bolt counterclockwise and 
tighten securely.

■

Install the spring into the string head housing and push 
down to seat.

■

Reinstall the spool. For the straight shaft attachment 
with the ReelEasy™ string  head, the spool should be 
placed so “This side out for straight shaft" is visible on 
the spool.

■

Replace the bump knob by inserting it into the centre 
of the spool.

■

Replace the string head cover, aligning latches with 

openings in the string head. Press cover and string 
head together until both latches snap into openings 
securely.

■

Attach the grass deflector to the blade guard and align 
the 3 screws on the grass defector to the screw holes 
on the blade guard.

NOTE

: Store the disassembled parts together for later 

use.

■

Install the cutting line. Refer to "String replacement" in 
the manual for additional information.

OPERATION

FUELING AND REFUELING

HANDLING FUEL SAFELY

 WARNING

 Check for fuel leaks. If any are found, correct 

them before using the product to prevent fire or 
burn injury.

■

Always handle fuel with care, it is highly flammable.

■

Always refuel outdoors where there are no sparks and 
flames. Do not inhale fuel vapors. Do not smoke.

■

Do not let petrol or lubricant come in contact with your 
skin.

■

Keep petrol and lubricant away from the eyes. If petrol 
or lubricant comes in contact with the eyes, wash 
them immediately with clean water. If irritation is still 
present, see a doctor immediately.

■

Clean up spilled petrol immediately.

■

Always transport and store fuel in a container approved 
for petrol.

MIXING THE FUEL

(See Fig 3)

■

The product is powered by a 2-stroke engine and 
requires pre-mixing petrol and 2-stroke lubricant. Pre-
mix unleaded petrol and 2-stroke engine lubricant in a 
clean container approved for petrol.

■

This engine is certified to operate on unleaded petrol 
intended for automotive use with an octane rating 
of 91 ([R + M] / 2) or higher.

■

Do not use any type of pre-mixed petrol / lubricant from 
fuel service stations, this includes the pre-mixed petrol / 
lubricant intended for use in mopeds, motorcycles, etc.

■

Use full synthetic 2-stroke lubricant only. Do not use 
automotive lubricant or 2-stroke outboard lubricant.