Makita LXT DUR184LZ - Инструкция по эксплуатации - Страница 9

9 ENGLISH

Electrical and battery safety

1. 

Avoid dangerous environment. Don't use the 

tool in damp or wet locations or expose it to 

rain. Water entering the tool will increase the 

risk of electric shock.

2. 

Recharge only with the charger specified by 

the manufacturer. A charger that is suitable for 

one type of battery pack may create a risk of 

fire when used with another battery pack.

3. 

Use power tools only with specifically desig

-

nated battery packs. Use of any other battery 

packs may create a risk of injury and fire.

4. 

When battery pack is not in use, keep it away 

from other metal objects, like paper clips, 

coins, keys, nails, screws or other small metal 

objects, that can make a connection from one 

terminal to another. Shorting the battery termi-

nals together may cause burns or a fire.

5. 

Under abusive conditions, liquid may be 

ejected from the battery; avoid contact. If con

-

tact accidentally occurs, flush with water. If 

liquid contacts eyes, seek medical help. Liquid 

ejected from the battery may cause irritation or 

burns.

6. 

Do not dispose of the battery(ies) in a fire. The 

cell may explode. Check with local codes for 

possible special disposal instructions.

7. 

Do not open or mutilate the battery(ies). 

Released electrolyte is corrosive and may 

cause damage to the eyes or skin. It may be 

toxic if swallowed.

Starting up the tool

► 

Fig.3

1. 

Make sure that there are no children or other 

people within a working range of 15 meters 

(50 ft), also pay attention to any animals in the 

working vicinity. Otherwise stop using the tool.

2. 

Before use always check that the tool is safe 

for operation. Check the security of the cutting 

tool and the guard and the switch trigger/lever 

for easy and proper action. Check for clean 

and dry handles and test the on/off function of 

the switch.

3. 

Check damaged parts before further use of 

the tool. A guard or other part that is damaged 

should be carefully checked to determine 

that it will operate properly and perform its 

intended function. Check for alignment of 

moving parts, binding of moving parts, break-

age of parts, mounting, and any other condi-

tion that may affect its operation. A guard or 

other part that is damaged should be properly 

repaired or replaced by our authorized ser-

vice center unless indicated elsewhere in this 

manual.

4. 

Switch on the motor only when hands and feet 

are away from the cutting tool.

5. 

Before starting make sure that the cutting 

tool has no contact with hard objects such as 

branches, stones etc. as the cutting tool will 

revolve when starting.

Method of operation

1. 

Never operate the machine with damaged 

guards or without the guards in place.

2. 

Only use the tool in good light and visibility. 

During the winter season beware of slippery 

or wet areas, ice and snow (risk of slipping). 

Always ensure a safe footing.

3. 

Take care against injury to feet and hands from 

the cutting tool.

4. 

Keep hands and feet away from the cutting 

means at all times and especially when switch-

ing on the motor.

5. 

Never cut above waist height.

6. 

Never stand on a ladder and run the tool.

7. 

Never work on unstable surfaces.

8. 

Don't overreach. Keep proper footing and 

balance at all times.

9. 

Remove sand, stones, nails etc. found within 

the working range. Foreign particles may 

damage the cutting tool and can cause to be 

thrown away, resulting in a serious injury.

10. 

Should the cutting tool hit stones or other hard 

objects, immediately switch off the motor and 

inspect the cutting tool.

11. 

Before commencing cutting, the cutting tool 

must have reached full working speed.

12. 

During operation always hold the tool with 

both hands. Never hold the tool with one hand 

during use. Always ensure a safe footing.

13. 

All protective equipment such as guards 

supplied with the tool must be used during 

operation.

14. 

Except in case of emergency, never drop 

or cast the tool to the ground or this may 

severely damage the tool.

15. 

Never drag the tool on the ground when mov-

ing from place to place, the tool may become 

damaged if moved in this manner.

16. 

Always remove the battery cartridge from the tool:

— 

whenever leaving the tool unattended;

— 

before clearing a blockage;

— 

before checking, cleaning or working on 

the tool;

— 

before making any adjustments, chang

-

ing accessories or storing;

— 

whenever the tool starts vibrating 

unusually;

— 

whenever transporting the tool.

17. 

Don't force the tool. It will do the job better and 

with less likelihood of a risk of injury at the 

rate for which it was designed.

18. 

Do not operate power tools in explosive atmo-

spheres, such as in the presence of flammable 

liquids, gases or dust.

 Power tools create sparks 

which may ignite the dust or fumes.

19. 

Take a rest to prevent loss of control caused 

by fatigue.

 We recommend to take a 10 to 

20-minute rest every hour.

Maintenance instructions

1. 

The condition of the cutting tool, protective 

devices and shoulder strap must be checked 

before commencing work.

2. 

Turn off the motor and remove the battery 

cartridge before carrying out maintenance, 

replacing the cutting tool and cleaning the 

tool.