Makita LXT DUR184LZ - Инструкция по эксплуатации - Страница 14

14 ENGLISH

Replacing the nylon cord

WARNING:

Use nylon cord with diameter 

specified in “SPECIFICATIONS” only. Never use 

heavier line, metal wire, rope or the like.

 Use rec-

ommended nylon cord only, otherwise it may cause 

damage to the tool and result in serious personal 

injury.

WARNING:

Make sure that the cover of the 

nylon cutting head is secured to the housing 

properly as described below.

 Failure to properly 

secure the cover may cause the nylon cutting head to 

fly apart resulting in serious personal injury.

1.

Take off the cover from the housing, pressing two 

latches which are slotted section oppositely on the side 

of the housing.

► 

Fig.27

2.

  Cut a nylon line in 3 m (10 ft). Fold the cutting line 

in two halves, leave one of half longer 80-100 mm (3 - 4 

inches) than another.

► 

Fig.28

3.

Hook the middle of the new nylon cord to the 

notch located at the center of the spool between the 2 

channels provided for the nylon cord. 

Wind both ends firmly around the spool in the direction 

marked on the head for right hand direction indicated 

by RH.

► 

Fig.29

4.

  Wind all but about 100 mm (4”) of the cords, leav

-

ing the ends temporarily hooked through a notch on the 

side of the spool.

► 

Fig.30

5.

Mount the spool on the cover so that the grooves 

and protrusions on the spool match up with those on the 

cover. Now, unhook the ends of the cord from their tem-

porary position and feed the cords through the eyelets 

to come out of the cover.

► 

Fig.31

6.

Align the protrusion on the underside of the cover 

with the slots of the eyelets. Then push the cover firmly 

onto the housing to secure it. Make sure the latches 

fully spread in the cover.

► 

Fig.32

To maintain product SAFETY and RELIABILITY, 

repairs, any other maintenance or adjustment should 

be performed by Makita Authorized or Factory Service 

Centers, always using Makita replacement parts.

TROUBLE SHOOTING

Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, 

do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace

-

ment parts for repairs.

State of abnormality

Probable cause (malfunction)

Remedy

Motor does not run.

Battery cartridge is not installed.

Install the battery cartridge.

Battery problem (under voltage)

Recharge the battery. If recharging is not effective, 

replace battery.

The drive system does not work 

correctly.

Ask your local authorized service center for repair.

Motor stops running after a little use. Battery's charge level is low.

Recharge the battery. If recharging is not effective, 

replace battery.

Overheating.

Stop using of tool to allow it to cool down.

It does not reach maximum RPM.

Battery is installed improperly.

Install the battery cartridge as described in this 

manual.

Battery power is dropping.

Recharge the battery. If recharging is not effective, 

replace battery.

The drive system does not work 

correctly.

Ask your local authorized service center for repair.

Cutting tool does not rotate: 

 stop the machine immediately!

Foreign object such as a branch is 

jammed between the guard and the 

nylon cutting head.

Remove the foreign object.

The drive system does not work 

correctly.

Ask your local authorized service center for repair.

Abnormal vibration: 

 stop the machine immediately!

One end of the nylon cord has been 

broken.

Tap the nylon cutting head against the ground while 

it is rotating to cause the cord to feed.

The drive system does not work 

correctly.

Ask your local authorized service center for repair.

Cutting tool and motor cannot stop: 

 Remove the battery immediately!

Electric or electronic malfunction.

Remove the battery and ask your local authorized 

service center for repair.