Einhell X-Change GE-CC 18 Li Solo - Инструкция по эксплуатации - Страница 19

GB

- 19 -

5.2 Height adjustment (Fig. 7)

Undo the union nut (Fig. 7/Item 5) until the paving 

scraper’s handle can be moved in and out freely. 

Now set the required working height and secure 

the handle in this position by tightening the union 

nut again.

5.3 Adjusting the additional handle (Fig. 8)

Undo the adjustment lock (Fig. 8/Item 3) for the 

additional handle until it can be moved forwards 

and backwards without any great resistance. Set 

the required position and tighten the securing 

screw again.

5.4. Installing the battery (Fig. 9/10)

Press the side pushlock button of the battery 

pack as shown in Fig. 9 and push the battery 

pack into the mount provided. When the battery 

is positioned as in Fig. 10, make sure that the 

pushlock button latches in place! To remove the 

battery pack, proceed in reverse order.

5.5 Charging the battery (Fig. 11)

1.  Take the battery pack out of the equipment. 

Do this by pressing the side pushlock buttons.

2.  Check that your mains voltage is the same as 

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

(14) into the socket outlet. The green LED will 

then begin to 

fl

 ash.

3.  Insert the battery pack (13) into the battery 

charger (14).

4.  In the section entitled „Charger indicator“ you 

will 

fi

 nd a table with an explanation of the LED 

indicator on the charger.

The battery pack can become a little warm during 

the charging. This is normal.

If the battery pack fails to charge, check:

• 

 voltage at the power socket

• 

 whether there is good contact at the charging 

contacts.

If the battery pack still fails to charge, send 

• 

 the charging unit

• 

 and the battery pack

to our customer service center.

To ensure that the battery pack provides long ser-

vice, you should take care to recharge it promptly. 

You must recharge the battery pack when you 

notice that the power of the cordless paving 

scraper drops. Never allow the battery pack to 

become fully discharged. This will cause it to de-

velop a defect.

5.6 Battery capacity indicator (Fig. 11b)

Press the switch for the battery capacity indicator 

(Fig. 11b/Item A). The battery capacity indicator 

(Fig. 11b/Item B) shows the charge status of the 

battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED 

fl

 ashes:

The battery is empty, recharge the battery.

All LEDs 

fl

 ash:

The battery pack has undergone exhaustive di-

scharge and is defective. Do not use or charge a 

defective battery pack!

6. Operation

To obtain maximum performance from your pa-

ving scraper, please follow the instructions given 

below:

• 

 Never use the paving scraper without the gu-

ard.

• 

 To switch on your paving scraper press the 

safety lock-off (Fig. 2/Item 1) and then press 

the On/Off switch (Fig. 2/Item 2).

• 

 To switch off your paving scraper, let go of the 

On/Off switch again (Fig. 2/Item 2).

One steel brush (Fig. 2/Item 9) and one nylon 

brush (Fig 2/Item 8) are supplied with the equip-

ment. The wire brush is suited for use on robust 

surfaces and obstinate weeds. We recommend 

using the nylon brush for light vegetation and sur-

faces too sensitive for the steel brush.

Important! Always carry out a short trial run 

to check out possible e

ff

 ects on the surfaces 

of the paving stones or slabs before starting 

with your work. Never use the equipment on 

very sensitive surfaces, for example tiles.

Important! Only use brushes which are in 

fl

 awless condition. Replace excessively worn 

or damaged brushes immediately.

Anl_GE_CC_18_Li_SPK7.indb   19

Anl_GE_CC_18_Li_SPK7.indb   19

25.08.2016   14:59:45

25.08.2016   14:59:45