Decker GL7033 - Инструкция по эксплуатации - Страница 8

8

ENGLISH

♦

  If  the  supply  cord  is  damaged,  it  must  be  re-

placed  by  the  manufacturer  or  an  authorised 
Black & Decker Service Centre in order to avoid 
a hazard.

♦

  Electric safety can be further improved by using 

a highsensitivity 30 mA Residual Current Device 
(RCD).

Features

This appliance includes some or all of the following 
features.
1. On/Off 

switch

2. Handle
3. Cable 

restraint

4. Power 

inlet

5. Secondary 

handle

6. Adjustment 

button

7. Tube
8.  Spare spool storage
9. HDL 

cap

10. Guard
11.  Line trimming blade
12. Spool housing
13. Cutting line
14. Edge wheel

Assembly

Warning! 

Before assembly, make sure that the tool 

is switched off and unplugged.

Fitting the guard (

fi

 g. A & B)

♦

  Remove the screw (15) from the guard (10).

♦

  Place the guard (10) onto the tool as shown.

♦

  Firmly press the guard until it snaps into place.

♦

  Secure the guard with the screw.

♦

  Tighten the screw.

Warning! 

Never use the tool unless the guard is 

properly 

fi

 tted.

Attaching the secondary handle (

fi

 g. C)

♦

  Press in and hold the adjustment button (6) on 

the side of the main body.

♦

  Slide the secondary handle (5) in place over the 

adjustment button (6).

Warning! 

Ensure that the teeth on the button are 

correctly aligned in slots in the handle and that the 
handle is secure.

Adjusting the position of the secondary 
handle (

fi

 g. D)

The secondary handle (5) can be adjusted to provide 
optimum balance and comfort.

♦

  Press in the adjustment button (6) on the left 

side of the handle.

♦

  Rotate the second handle (5) into the required 

position.

♦

  Release the adjustment button (6).

Warning! 

Ensure that the teeth on the button are 

correctly aligned in slots in the handle and that the 
handle is secure.

Adjusting the height of the tool (

fi

 g. E & 

F)

This tool has a telescopic mechanism, allowing you 
to set it to a comfortable height. There are multiple 
height settings. To adjust the height setting, proceed 
as follows:

♦

  Release the height adjust locking clamp (16).

♦

  Gently pull the tube (7) up or down to the desired 

height.

♦

  Close the height adjust locking clamp (16).

Releasing the cutting line

In  transit,  the  cutting  line  is  taped  to  the  spool 
housing.

♦

  Remove the tape holding the cutting line to the 

spool housing (12).

Storing the spool not in use (

fi

 g. G)

The tool has two cutting systems:

♦

AFS: 

Single line autofeed for light trimming and 

edging.

♦

HDL: 

Heavy Duty Dual Line cutting system for 

more overgrown areas.

Note: 

The HDL spool may be used in trimming 

mode only.
The cutting system not in use can be stored in the 
spare spool storage (GL8033 & GL9035 Only).

♦

  Align the tabs (17) on the spool cover with the 

cut outs (18) in the spare spool storage (8).

♦

  Push the cover onto the spare spool storage 

until it snaps securely into place.

Connecting the tool to the mains (

fi

 g. H)

♦

  Connect the female plug of a suitable extension 

cable to the power inlet (4).

♦

  Loop the cable through the cable restraint (3).

♦

  Insert the mains plug into a mains outlet.

For wired in cable units: Make sure the cable is 
looped through the cable restraint prior to connect-
ing the plug to the mains outlet.

Warning! 

The extension cable must be suitable for 

outdoor use.

Use

Warning! 

Let the tool work at its own pace. Do not 

overload.