Microlife BP A100 Plus - Инструкция по эксплуатации - Страница 8

6

Flat battery – replacement

When the batteries are flat, the battery symbol 

AO

 will flash as soon 

as the instrument is switched on (flat battery displayed). You cannot 

take any further measurements and must replace the batteries.

Which batteries and which procedure?

Using rechargeable batteries

You can also operate this instrument using rechargeable batteries.

10. Using a Mains Adapter

You can operate this instrument using the Microlife mains adapter 

(DC 6V, 600mA). 

When the mains adapter is connected, no battery current is consumed.

11. Error Messages

If an error occurs during the measurement, the measurement is 

interrupted and an error message, e.g. «

ERR 3

», is displayed.

* Please consult your doctor, if this or any other problem occurs repeatedly.

1. Open the battery compartment 

7

 at the back of the instrument 

by pushing inwards at the two arrows and pulling out the 

battery compartment cover.

2. Replace the batteries – ensure correct polarity as shown by the 

symbols in the compartment.

3. To set date and time, follow the procedure described in «Section 2.».

H

The memory retains all values although date and time (and 

possibly also set alarm times) must be reset – the year 

number therefore flashes automatically after the batteries 

are replaced.

H

Use 4 new, long-life 1.5V, size AA batteries.

H

Do not use batteries beyond their date of expiry.

H

Remove batteries if the instrument is not going to be used 

for a prolonged period.

H

Only use «NiMH» type reusable batteries.

H

Batteries must be removed and recharged when the flat 

battery symbol appears. They should not remain inside the 

instrument as they may become damaged (total discharge as 

a result of low use of the instrument, even when switched off).

H

Always remove the rechargeable batteries if you do not 

intend to use the instrument for a week or more.

H

Batteries cannot be charged in the blood pressure monitor. 

Recharge batteries in an external charger and observe the 

information regarding charging, care and durability.

H

Only use the Microlife mains adapter available as an orig-

inal accessory appropriate for your supply voltage, e.g. the 

«Microlife 230V adapter».

H

Ensure that neither the mains adapter nor the cable are 

damaged.

1. Plug the adapter cable into the mains adapter socket 

5

 in the 

blood pressure monitor.

2. Plug the adapter plug into the wall socket.

Error

Description Potential cause and remedy

«

ERR 1

» Signal too 

weak

The pulse signals on the cuff are too weak. 

Re-position the cuff and repeat the 

measurement.*

«

ERR 2

» Error signal During the measurement, error signals were 

detected by the cuff, caused for instance by 

movement or muscle tension. Repeat the 

measurement, keeping your arm still.

«

ERR 3

» No pressure 

in the cuff

An adequate pressure cannot be generated 

in the cuff. A leak may have occurred. Check 

that the cuff is correctly connected and is 

not too loose. Replace the batteries if 

necessary. Repeat the measurement.

«

ERR 5

» Abnormal 

result

The measuring signals are inaccurate and 

no result can therefore be displayed. Read 

through the checklist for performing reliable 

measurements and then repeat the 

measurement.*

«

ERR 6

» MAM Mode  There were too many errors during the 

measurement in MAM mode, making it 

impossible to obtain a final result. Read 

through the checklist for performing reli-

able measurements and then repeat the 

measurement.*

«

HI

»

Pulse or cuff 

pressure too 

high

The pressure in the cuff is too high (over 

300 mmHg) OR the pulse is too high (over 

200 beats per minute). Relax for 5 minutes 

and repeat the measurement.*

«

LO

»

Pulse too 

low

The pulse is too low (less than 40 beats per 

minute). Repeat the measurement.*

H

If you think the results are unusual, please read through the 

information in «Section 1.» carefully.