Skil 8003 - Инструкция по эксплуатации - Страница 7

7

d) 

Store idle power tools out of the reach of children 

and do not allow persons unfamiliar with the power 

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained 

users.

e) 

Maintain power tools. Check for misalignment or 

binding of moving parts, breakage of parts and any 

other condition that may affect the power tool's 

operation. If damaged, have the power tool repaired 

before use.

 Many accidents are caused by poorly 

maintained power tools.

f) 

Keep cutting tools sharp and clean.

 Properly 

maintained cutting tools with sharp cutting edges are 

less likely to bind and are easier to control.

g) 

Use the power tool, accessories and tool bits etc., 

in accordance with these instructions, taking into 

account the working conditions and the work to 

be performed.

 Use of the power tool for operations 

different from those intended could result in a hazardous 

situation.

5)  SERVICE

a) 

Have your power tool serviced by a qualified repair 

person using only identical replacement parts.

This will ensure that the safety of the power tool is 

maintained.

SAFETY INSTRUCTIONS FOR HEAT GUNS

BEFORE USE:

• 

Check the functioning of the tool before each use and, 

in case of a defect, have it repaired immediately by a 

qualified person; never open the tool yourself

• 

Inspect tool cord and plug before each use and, if 

damaged, have them replaced by a qualified person

• 

Use completely unrolled and safe extension cords with a 

capacity of 16 Amps (U.K. 13 Amps)

• 

Inspect the extension cord periodically and replace it, if 

damaged

• 

Use the tool and its accessories in accordance with this 

instruction manual and in the manner intended for the 

tool; use of the tool for operations, different from those 

normally expected to be performed by the tool, could 

result in a hazardous situation

• 

This tool should not be used by people under the age 

of 16 years

• 

This tool is not intended for use by persons (including 

children) with reduced physical, sensory or mental 

capabilities, or lack of experience and knowledge, 

unless they have been given supervision or instruction 

concerning use of the tool by a person responsible for 

their safety

• 

Always check that the supply voltage is the same as the 

voltage indicated on the nameplate of the tool

• 

Be sure tool is switched off when plugging in

DURING USE:

•  Handle the tool with care; prevent fire and burns

-

do not touch the air outlet/nozzle and the heated 

object; they become extremely hot

-

do not hold the air outlet/nozzle too close to the object 

to be worked on

-

do not direct the hot air flow towards the same surface 

for too long

-

never look down the air outlet/nozzle

-

wear protective gloves and use safety glasses

-

never direct the hot air flow towards persons or 

animals

-

never use the tool for drying hair

-

do not leave the tool unattended

-

never use the tool in the proximity of inflammable 

gases or combustible materials (

risk of explosion

)

-

when working with plastic, paint, varnish and similar 

materials, inflammable and poisonous gases may 

be produced; inform yourself beforehand about the 

materials to be worked on

-

take into account, that heat may be transferred to 

combustible materials out of eyesight

-

to be on the safe side, have a bucket of water or a fire 

extinguisher handy, in case any material catches fire

•  Prevent electrical shock

-

never poke anything down the air outlet/nozzle

-

avoid body contact with earthed surfaces (e.g. pipes, 

radiators, ranges, refrigerators)

-

ensure the tool does not get wet

-

do not use the tool in damp locations

-

when used outdoors, connect the tool via a fault 

current (FI) circuit breaker with a triggering current 

of 30 mA maximum, and only use an extension cord 

which is intended for outdoor use and equipped with a 

splashproof coupling-socket

•  Handle the cord with care

-

always keep away the cord from the hot air flow and 

the air outlet/nozzle

-

keep the cord away from heat, oil and sharp edges

-

do not carry the tool by the cord, and do not yank the 

cord to disconnect it from the socket

-

do not suspend the tool by the cord

• 

Never use the tool in conjunction with chemical solvents

• 

Make sure work area is adequately ventilated

• 

Keep work area clean and well lit

• 

Keep children away from work area

• 

Ensure that children do not play with the tool

• 

Inrush currents cause short-time voltage drops; under 

unfavourable power supply conditions, other equipment 

may be affected (if the system impedance of the power 

supply is lower than 0,127 + j0,079 Ohm, disturbances 

are unlikely to occur); if you need further clarification, 

you may contact your local power supply authority

• 

Stay alert; watch what you are doing, use common 

sense and do not operate the tool when you are tired

• 

Take a secure stance; do not overreach, especially on 

ladders and stages

• 

Ensure that the tool is switched off, before putting it 

aside

• 

In case of electrical or mechanical malfunction, 

immediately switch off the tool and disconnect the plug

AFTER USE:

• 

Switch off the tool and disconnect the plug

•  Allow the tool to cool down for at least 30 minutes 

before storage

• 

Suspend the tool on hanging ring J 

②

 or set it down on 

its rear in an upright position; when doing so, make sure 

no combustible materials or inflammable gases are in 

the proximity

• 

Do not store/leave the tool outdoors

• 

Store the tool in a dry and locked-up place, out of reach 

of children