Metabo BE 500/6 600343000 - Инструкция по эксплуатации - Страница 12

ENGLISH

en

11

7.3

Presetting the speed (depending on 

features)

Select the maximum speed using the preselection 
wheel (5). For recommended rotational speeds for 
drilling, see page 3.

7.4

On/Off switch, modifying the speed

Switching on, speed:

 press the trigger switch (6).

Press in the trigger to increase the rotational 
speed.
To switch off release the trigger switch.

Continuous activation:

 With the trigger (6) 

pressed, push in the locking button (7) and 
release the trigger. Press and release the trigger 
(6) again to switch off.

In continuous operation, the machine 
continues running if it is forced out of your 

hands. Therefore, always hold the machine with 
both hands using the handles provided, stand 
securely and concentrate.

7.5

Tool Change with Futuro Top Keyless 

Chuck (1)

See illustrations A, page 2.

Open chuck:

 Hold the retaining ring and turn the 

sleeve with your other hand in direction of the 
arrow -1-.

Fit the tool:

 Insert the tool -2- as far as possible. 

Hold the retaining ring and turn the sleeve as far as 
it will go with your other hand in direction of the 
arrow -3-.

7.6

Unscrewing the chuck 

(To screw without a chuck or when using 

attachments)

See illustration B, page 3.
Hold the drill spindle tight with the supplied open-
ended spanner. Clamp an Allen key in the chuck 
and strike lightly with a rubber hammer to loosen, 
then unscrew.
Tighten just as firmly.

The chuck must be screwed firmly to the 
spindle. If rotated counter-clockwise (e.g. 

when screwing) it could otherwise become loose.

Note:

 If a bit clamping bush (order no. 6.31281) is 

attached, the screwdriver bit inserted in the 
hexagon socket of the spindle is held in place.

7.7

LED lamp (depending on the features)

For working in badly lit areas. The LED light (9) 
lights up when the machine is switched on.

8.1

Only for cordless machines; the 

machine's multifunctional monitoring 

system

If the machine switches off automatically, the 
machine electronics have activated automatic 

protection mode.

In spite of this protective function, overloading 
is still possible with certain applications and 

can result in damage to the machine.

Causes and remedies:

1.

Battery pack almost flat

 (the electronics 

prevent the battery pack from discharging totally 
and avoid irreparable damage).
If one LED is flashing, the battery pack is almost 
flat. (13) If necessary, press the (14) button and 
check the LEDs (13) to see the charge level. If 
the battery pack is almost flat, it must be 
recharged.

2. Long continuous overloading of the machine will 

activate the 

temperature cut-out

.

Leave the machine or battery pack to cool. 
Note: If the battery pack feels very warm, the 
pack will cool more quickly in your "AIR 
COOLED" charger. 
Note: The machine will cool more quickly if you 
operate it at idling speed.

3. If the 

current is too high

 (for example, if the 

machine seizes continuously for long periods), 
the machine switches off.
Switch off the machine at the trigger switch (6). 
Then continue working as normal. Try to prevent 
the machine from seizing.

ENG

Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements 
and specifications listed in these operating 
instructions. 
Fit accessories securely. Secure the machine if it is 
operated in a bracket. Loss of control can cause 
personal injury.

A Battery chargers: ASC Ultra, ASC 15, ASC 30 

and others.

B Battery packs 18 Volt: 5.2 Ah (6.25592); 4.0 Ah 

(6.25591); 3.0 Ah (6.25594)

See www.metabo.com or the catalogue for a 
complete range of accessories.

Repairs to electrical tools must ONLY be carried out 
by qualified electricians! 
Contact your local Metabo representative if you 
have Metabo power tools requiring repairs. See 
www.metabo.com for addresses.
You can download a list of spare parts from 
www.metabo.com.

Observe national regulations on environmentally 
compatible disposal and on the recycling of disused 
machines, packaging and accessories.

Only for EU countries: never dispose of 
power tools in your household waste! Used 
power tools must be collected separately and 

8. Troubleshooting

9. Accessories

10. Repairs

11. Environmental Protection