FESTOOL MX 1000 E EF HS2 767999 - Инструкция по эксплуатации - Страница 15

15

6 

Starting up and using the machine

 WARNING 

Risk of accident if the machine is operated us-

ing unauthorised voltages or frequencies. 



The mains voltage and the frequency of the 

power source must correspond with the 

specifi cations on the machine’s name plate. 



In North America, only Festool machines with 

the voltage specifi cations 120 V/60 Hz may 

be used.

 WARNING

Risk of accident, electric shock



Always pull the plug out of the socket before 

performing any type of work on the machine. 

CAUTION

Inhaling the dust may damage the respiratory 

tract.



When working with dust, you must wear res-

piratory protection.

6.1 

Tightening the stirrer (see Fig. [2])



Screw in the stirrer 

[2-3]

 with endpiece M14x2 

(wrench size 22) by turning it to the right in the 

adapter ErgoFix 

[2-1]

 (wrench size 19) and use 

the wrench to tighten it.



Fasten the ErgoFix adapter to the stirrer bar, 

then insert the assembled stirrer into the slot 

of the spindle. 

To set-up the working height see chapter 6.5.

6.2 

Switching the machine on and off

  Always hold the machine with both hands.

Pressing the switch 

[1-3]

 puts the machine into 

operation and taking your hand away from the 

switch stops the machine from working.

Using the switch button to control the speed (ac-

celeration function switch)

You can use the switch 

[1-3]

 to change the level 

of the speed until it reaches the speed range that 

is set by the speed controller.

Continuous operation

By pressing the switch 

[1-3]

 as far as it goes and 

pressing the locking switch button 

[1-4]

 at the 

same time, you can activate continuous operation. 

Press and release the switch button 

[1-3]

 again 

to switch off continuous operation.

6.3 Control 

electronics

Limiting the starting current

The electronically-controlled soft start ensures 

that the machine starts up smoothly.
At the same time, this also prevents the materi-

als to be stirred from spurting out of the mixing 

container. Thanks to the low starting current of 

the machine, a 10 A fuse is suffi cient.

Electronic speed preselection

You can use the speed controller 

[1-5]

 to set the 

speed:

MX 1000 E EF, MX 1200 E EF

Level 1 

360 Level 4 

520

Level 2 

410 Level 5 

580

Level 3 

470 Level 6 

630

MX 1000/2 E EF

1st speed

2nd speed

Level 1 

360 Level 1 

580

Level 2 

410 Level 2 

670

Level 3 

470 Level 3 

760

Level 4 

520 Level 4 

840

Level 5 

580 Level 5 

930

Level 6 

630 Level 6 

1010

The speed depends on the stirrer rod that is used 

and on the material that you want to process.

Overload protection

An electronic overload protection protects the mo-

tor from damage if there is an extreme overload.
In this case, the motor remains at a standstill and 

only starts up again once the load has been re-

moved. To restart the machine, you must switch 

it on again.

Constant Electronic function

The Constant Electronic function maintains an 

almost constant speed and load; this ensures that 

the material is stirred evenly.

Temperature-dependent overload protection

(VALID for the type MX 1000/2 E EF and 
MX 1200 E EF)

To protect the machine against overheating if you 

are using it for an extremely prolonged period, 

switch the safety electronics to the cooling mode 

as soon as the critical temperature is reached. 

You cannot load the machine and it runs at a re-

duced speed. Approx. 2 minutes after cooling, the 

machine is again ready for use and fully able to