FERM FX Power CDM1164 - Инструкция по эксплуатации - Страница 6

6

EN

f)  

Keep cutting tools sharp and clean. 

Properly maintained cutting tools with sharp 
cutting edges are less likely to bind and are 
easier to control.

g)  

Use the power tool, accessories and 
tool bits etc. in accordance with these 
instructions, taking into account the 
working conditions and the work to 
be performed. 

Use of the power tool for 

operations different from those intended could 
result in a hazardous situation.

h)

Keep handles and grasping surfaces dry, 
clean and free from oil and grease.

 Slippery 

handles and grasping surfaces do not allow 
for safe handling and control of the tool in 
unexpected situations.

5)   Battery tool use and care

a)  

Recharge only with the charger specified by 

the manufacturer

. 

A charger that is suitable 

for one type of battery pack may create a risk 

of fire when used with another battery pack.

b)  

Use power tools only with specifically 

designated battery packs. 

Use of any other 

battery packs may create a risk of injury and fire.

c)  

When battery pack is not in use, keep it 
away from other metal objects, like paper 
clips, coins, keys, nails, screws or other 
small metal objects that can make a 
connection from one terminal to another

. 

Shorting the battery terminals together may 

cause burns or a fire.

d)  

Under abusive conditions, liquid may be 
ejected from the battery; avoid contact. 

If contact accidentally occurs, flush with 

water. If liquid contacts eyes, additionally 
seek medical help

. 

Liquid ejected from the 

battery may cause irritation or burns.

e)  

Do not use a battery pack or tool that is 

damaged or modified.

Damaged or modified 

batteries may exhibit unpredictable behaviour 

resulting in fire, explosion or risk of injury.

f)  

Do not expose a battery pack or tool to 

fire or excessive temperature.

Exposure to 

fire or temperature above 130 °C may cause 
explosion. NOTE The temperature „130 °C“ 
can be replaced by the temperature „265 °F“.

g)  

Follow all charging instructions and do not 
charge the battery pack or tool outside 

the temperature range specified in the 

instructions.

Charging improperly or at 

temperatures outside the specified range may 
damage the battery and increase the risk of fire.

6)   Service

a)  

Have your power tool serviced by a 

qualified repair person using only identical 

replacement parts. 

This will ensure that the 

safety of the power tool is maintained.

b)  

Never service damaged battery packs.

Service of battery packs should only be 
performed by the manufacturer or authorized 
service providers.

Additional safety warnings for drills 

and screw drivers

a)    

Hold the power tool by insulated gripping 
surfaces, when performing an operation 
where the cutting accessory or fasteners 
may contact hidden wiring. 

Cutting 

accessory contacting a “live” wire may make 
exposed metal parts of the power tool “live” 
and could give the operator an electric shock.

”

Safety instructions when using long 

drill bits

a) 

 Never operate at higher speed than the 
maximum speed rating of the drill bit.

At higher speeds, the bit is likely to bend if 
allowed to rotate freely without contacting the 
workpiece, resulting in personal injury.

b)    

Always start drilling at low speed and with 
the bit tip in contact with the workpiece. 

At higher speeds, the bit is likely to bend if 
allowed to rotate freely without contacting the 
workpiece, resulting in personal injury.

c)  

 Apply pressure only in direct line with the bit 
and do not apply excessive pressure.

Bits 

can bend causing breakage or loss of control, 
resulting in personal injury.

For the charger

Intended use

Charge only 20V (recommended) 2.0Ah or 4.0Ah 
Li-ion type rechargeable battery packs. Other 
types of batteries may burst causing personal 
injury and damage.
a)

   The appliance is not to be used by persons 

(including children) with reduced physical, 
sensory or mental capabilities, or lack of 
experience and knowledge, unless they 
have been given supervision or instruction