DEWALT DWD 014 S - Инструкция по эксплуатации - Страница 28

E N G L I S H

26

KEYLESS CHUCK INSTALLATION (FIG. 6)

Screw the chuck on by hand as far as it will go. 
Tighten the chuck around the shorter end of a hex 
key (not supplied) and strike the longer end in the 
clockwise direction with a soft hammer.

OPERATION

Instructions for Use

  WARNING: 

Always observe the safety 

instructions and applicable regulations.

Trigger Switch (fi g. 1)

To start the drill, depress the trigger switch; to stop 
the drill, release the trigger switch.

NOTE: 

Use lower speeds for starting holes without 

a center punch, drilling in metal or plastics, driving 
screws or drilling ceramics. Higher speeds are better 
for drilling wood and composition boards and using 
abrasive and polishing accessories.

VARIABLE SPEED

A variable speed trigger switch (a) permits speed 
control—the farther the trigger is depressed, the 
higher the speed of the drill.

For continuous operation, press and hold the 
variable speed switch, move the lock-on button (b) 
up, then release the switch.

To stop continuous operation, press the switch 
briefly and release it. Always switch the tool off when 
work is finished and before unplugging.

Speed Dial (fi g. 1)

DWD014, DWD014S

To reduce the speed, turn the speed dial (g) 
counterclockwise. To increase speed, turn the dial 
clockwise.

Proper Hand Position (fi g. 7)

WARNING: 

To reduce the risk of 

serious personal injury, 

ALWAYS

use proper hand position as shown 
in figure 7. 

WARNING:

 To reduce the risk of 

serious personal injury, 

ALWAYS

 hold 

securely in anticipation of a sudden 
reaction.  

Proper hand position requires one hand under the 
the housing, with the other hand on the main handle 
(h).  

Drilling

  WARNING: To reduce the risk 

of serious personal injury, turn 
tool off and disconnect tool from 
power source before making any 
adjustments or removing/installing 
attachments or accessories.

  WARNING: 

To reduce the risk of 

personal injury,

ALWAYS ensure 

workpiece is anchored or clamped 
firmly. If drilling thin material, use a wood 
“back-up” block to prevent damage to 
the material.

  1.  Use sharp drill bits only. For WOOD, use the 

low speed setting and twist drill bits, spade bits, 
power auger bits, or hole saws. For METAL, use 
the low speed setting and steel twist drill bits or 
hole saws. 

  2.  Always apply pressure in a straight line with the 

bit. Use enough pressure to keep drill biting, but 
do not push hard enough to stall the motor or 
deflect the bit.

  3.  Hold tool firmly with both hands to control the 

twisting action of the drill.

  CAUTION: 

Drill may stall if overloaded 

causing a sudden twist. Always expect 
the stall. Grip the drill firmly to control 
the twisting action and avoid injury.

 4.

  IF DRILL STALLS

, it is usually because 

it is being overloaded or improperly used. 

RELEASE TRIGGER IMMEDIATELY

, remove 

drill bit from work, and determine cause of 
stalling. 

DO NOT CLICK TRIGGER ON 

AND OFF IN AN ATTEMPT TO START A 
STALLED DRILL — THIS CAN DAMAGE 
THE DRILL

.

  5.  To minimize stalling or breaking through the 

material, reduce pressure on drill and ease the 
bit through the last fractional part of the hole.

  6.  Keep the motor running when pulling the bit 

back out of a drilled hole. This will help prevent 
jamming.

  7.  With variable speed drills there is no need to 

center punch the point to be drilled. Use a 
slow speed to start the hole and accelerate by 
squeezing the trigger harder when the hole is 
deep enough to drill without the bit skipping out. 

DRILLING IN METAL 

Start drilling with slow speed and increase to full 
power while applying firm pressure on the tool. 
A smooth even flow of metal chips indicates the 
proper drilling rate. Use a cutting lubricant when