Bosch GSB 19-2 RE (БЗП) 060117B500 - Инструкция по эксплуатации - Страница 14

14

 | English

Noise/vibration information

Noise emission values determined according to

EN 62841-2-1

.

Typically the A-weighted noise level of the power tool are: 

99

dB(A); sound power level 

110

 dB(A). Uncertainty K = 

5

 dB.

Wear hearing protection!

Vibration total values a

h

 (triax vector sum) and uncertainty K

determined according to 

EN 62841-2-1

.

Drilling into metal: a

h

=

3.5

 m/s

2

, K=

1.5

 m/s

2

Impact drilling into concrete: a

h

=

17

 m/s

2

, K=

1.5

 m/s

2

Screwdriving: a

h

<

2.5

 m/s

2

, K=

1.5

 m/s

2

Thread cutting: a

h

<

2.5

 m/s

2

, K=

1.5

 m/s

2

The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.

Assembly

u

Pull the plug out of the socket before carrying out any
work on the power tool.

Auxiliary handle (see figure A)

u

Do not operate your power tool without the auxiliary
handle

(8)

.

You can adjust the auxiliary handle 

(8)

 to any of 12 positions

in order to achieve a safe work posture that minimises fa-
tigue.
Turn the lower gripping end of the auxiliary handle 

(8)

 in ro-

tational direction 

➊

 and push the auxiliary handle 

(8)

 for-

ward until you can swivel it into the required position. Then
pull the auxiliary handle 

(8)

 back again and turn the lower

gripping end in rotational direction 

➋

 to tighten it.

Setting the Drilling Depth (see figure A)

You can use the depth stop 

(9)

 to set the required drilling

depth 

X

.

Turn the lower gripping end of the auxiliary handle 

(8)

 anti-

clockwise and set the depth stop 

(9)

.

Pull the depth stop 

(9)

 far enough out that the distance

between the drill bit tip and the edge of the depth stop 

(9)

corresponds to the required drilling depth 

X

.

Then turn the lower gripping end of the auxiliary handle 

(8)

clockwise to retighten it.
The fluting on the depth stop 

(9)

 must face upwards.

Changing the tool

u

Wear protective gloves when changing tools.

 The drill

chuck may heat up significantly when it is used for long
periods.

Keyless chuck (GSB 19-2 RE) (see figure B)

The drill spindle is locked when the on/off switch 

(6)

 is not

pressed. This makes it possible to change the application
tool in the drill chuck quickly, conveniently and easily.
Open the keyless chuck 

(1)

 by turning it in the direction of

rotation 

➊

 until the tool can be inserted. Insert the tool.

Firmly tighten the sleeve of the keyless chuck 

(1)

 by turning

it by hand in the rotational direction 

➋

 until it stops clicking.

This will automatically lock the drill chuck.
The lock will disengage again if you turn the sleeve in the op-
posite direction to remove the tool.

Keyless chuck (GSB 780) (see figure C)

Hold the rear sleeve 

(12)

 of the keyless chuck 

(1)

 firmly and

turn the front sleeve 

(11)

 in the rotational direction 

➊

 until

the tool can be inserted. Insert the tool.
Hold the rear sleeve 

(12)

 of the keyless chuck 

(1)

 and firmly

tighten the front sleeve 

(11)

 by hand in the rotational direc-

tion 

➋

 until it stops clicking. This will automatically lock the

drill chuck.
The lock will disengage again if you turn the front sleeve 

(11)

in the opposite direction to remove the tool.

Keyed chuck (see figure D)

Open the keyed chuck 

(14)

 by turning it until the tool can be

inserted. Insert the tool.
Insert the chuck key 

(13)

 into the corresponding holes of the

keyed chuck 

(14)

 and clamp the tool evenly.

Screwdriving tools (see figure E)

You should always use a universal bit holder 

(16)

 when using

screwdriver bits 

(15)

. Only use screwdriver bits that fit the

screw head.
For screwdriving, make sure the "drilling/impact drilling" se-
lector switch 

(2)

 is always set to the "drilling" symbol.

Changing the drill chuck

u

Pull the plug out of the socket before carrying out any
work on the power tool.

Removing the Drill Chuck (see figure F)

Remove the auxiliary handle 

(8)

 and set the gear selector

switch 

(7)

 to the middle position between first and second

gear.

1 609 92A 6RA | (16.09.2021)

Bosch Power Tools