Шуруповерты Bosch ANGLE EXACT ION 15-500 0.602.494.601 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
English |
17
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
u
Only use the battery with products from the manufac-
turer.
This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture.
There is a risk of explosion and
short-circuiting.
u
Switch the power tool off immediately if the applica-
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback.
The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
WARNING
The dust produced by sanding,
sawing, grinding, drilling and
other similar activities may cause cancer, congenital de-
fects or genetic mutations
. Some of these dusts contain
substances such as:
Lead in lead-based paint and varnish; crystalline silica in
bricks, cement and other building materials; arsenic and
chromate in chemically treated wood. The risk of becoming
ill depends on how frequently you are exposed to these sub-
stances. To reduce the potential danger, you should always
wear adequate personal protective equipment (e.g. specially
made breathing apparatus that can filter out even the smal-
lest of dust particles) and work only in well-ventilated areas.
u
Avoid switching on the tool accidentally. Make sure
that the on/off switch is set to the off position before
inserting a battery.
Accidents can occur as a result of
carrying the power tool with your finger on the on/off
switch or inserting the battery while the power tool is
switched on.
u
Do not use application tools that are worn or in other-
wise less than perfect condition.
Defective application
tools can break, for example, causing material damage
and personal injury.
u
When fitting an application tool, make sure that it is
held securely in the tool holder.
If the application tool is
not held securely in the tool holder, it may become loose
and consequently uncontrollable.
u
Be careful when screwing in long screws – there is a
risk of slipping when using particular screws and ap-
plication tools.
Long screws are often difficult to control
and there is a danger that you will slip and hurt yourself
when screwing them in.
u
Check which rotational direction is set before switch-
ing on the power tool.
If you want to loosen a screw but
the rotational direction is set to tighten the screw, for ex-
ample, the power tool may move violently and uncontrol-
lably.
u
Do not use the power tool as a drill.
Power tools with a
shut-off clutch are not suitable for drilling. The clutch can
shut off automatically and without warning.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for tightening and loosening
screws, bolts, nuts and other threaded connectors in the
specified power and dimension ranges.
The power tool is suitable only for use in industrial environ-
ments.
The power tool is not suitable for use as a drill.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1)
Application tool
A)
(2)
Tool holder
A)
(3)
Angled screw head
A)
(4)
Spanner flat on the angled head flange
A)
(5)
Spanner flat on the cap nut
(6)
Slider for preselecting the torque
(7)
LED indicator for screwdriving applications
(8)
Battery charge indicator
(9)
Battery
A)
(10)
On/off switch
(11)
Rotational direction switch
(12)
LED holder
(13)
Worklight
(14)
Battery release button
A)
(15)
Hanging hook
A)
(16)
Attachment slots for hanging hook
(17)
Marking ring
(18)
Spring ring
(19)
Cavity in the housing shell
(20)
Open-ended spanner (27 mm width across flats)
A)
(21)
Open-ended spanner (22 mm width across flats)
A)
(22)
Lock nut
(23)
Motor housing
(24)
Quick-change chuck
A)
(25)
Adjustment tool
(26)
Hex key
A)
(27)
Adjustment disc
Bosch Power Tools
1 609 92A 4R1 | (21.02.2019)
