Black Decker KR 50 RE - Инструкция по эксплуатации - Страница 4

4

ENGLISH

d.  Store idle power tools out of the reach 

of children and do not allow persons 
unfamiliar with the power tool or these 
instructions to operate the power tool. 

Power tools are dangerous in the hands of 
untrained users.

e.  Maintain power tools. Check for 

misalignment or binding of moving parts, 
breakage of parts and any other condition 
that may affect the power tools operation. 
If damaged, have the power tool repaired 
before use.

 Many accidents are caused by 

poorly maintained power tools.

f.  Keep cutting tools sharp and clean.

 Properly 

maintained cutting tools with sharp cutting 
edges are less likely to bind and are easier to 
control.

g.  Use the power tool, accessories and 

tool bits etc., in accordance with these 
instructions and in the manner intended 
for the particular type of power tool, taking 
into account the working conditions and 
the work to be performed.

 Use of the power 

tool for operations different from those intended 
could result in a hazardous situation.

5. Service
a.  Have your power tool serviced by a 

qualifi ed repair person using only identical 
replacement parts.

 This will ensure that the 

safety of the power tool is maintained.

Additional safety instructions for impact drills

• 

Wear ear protectors with impact drills.

Exposure to noise can cause hearing loss.

• 

Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

• 

Hold power tool by insulated gripping 
surfaces when performing an operation 
where the cutting tool may contact hidden 
wiring or its own cord. 

Contact with a “live” 

wire will also make exposed metal parts of the 
power tool “live” and shock the operator.

• 

Use clamps or another practical way to 
secure and support the workpiece to 
a stable platform.

 Holding the work by hand or 

against your body leaves it unstable and may 
lead to loss of control.

•  Before drilling into walls, fl oors or ceilings 

check for the location of wiring and pipes.

•  Avoid touching the tip of a drill bit just after 

drilling, as it may be hot.

Electrical safety

This tool is double insulated; therefore 
no earth wire is required. Always check 
that the power supply corresponds to the 
voltage on the rating plate.

•  This appliance is not intended for use by young 

or infi rm persons without supervision. Children 
must be supervised to ensure they do not play 
with the appliance.

•  If the supply cord is damaged, it must be 

replaced by the manufacturer or an authorised 
Black & Decker Service Centre in order to 
avoid a hazard.

Features

This tool includes some or all of the following 
features.
1.  Variable speed switch
2. Lock-on 

button

3. Forward/reverse 

slider

4. Drilling 

mode 

selector

5. Chuck
6. Depth 

stop

7. Side 

handle

Assembly

Warning!

 Before assembly, make sure that the tool 

is switched off and unplugged.

Fitting the side handle and depth stop (fi g. A)

•  Turn the grip counterclockwise until you can 

slide the side handle (7) onto the front of the 
tool as shown.

•  Rotate the side handle into the desired 

position.

•  Insert the depth stop (6) into the mounting hole 

as shown.

•  Set the drilling depth as described below.
•  Tighten the side handle by turning the grip 

clockwise.

Fitting a drill bit or screwdriver bit

Keyless chuck (fi g. B)

•  Open the chuck by turning the front part (8) 

with one hand while holding the rear part (9) 
with the other.

•  Insert the bit shaft (10) into the chuck and fi rmly 

tighten the chuck.

Keyed chuck (fi g. C)

•  Open the chuck by turning the sleeve (11) 

counterclockwise.

•  Insert the bit shaft (10) into the chuck.