Metabo MFE 65 - Инструкция по эксплуатации - Страница 15

ENGLISH

en

15

To clean the motor: 

To prevent stone dust from 

collecting inside the wall chaser, you must 

occasionally clean the motor by blowing 

compressed air through the air duct on the back of 

the motor housing, if the machine is used for 

extended periods. If possible, this process should 

NOT be carried out indoors/in a confined space.

Button  (7) for adjusting the handle: 

Occasionally blow compressed air through the 

button (when pressed, in all 3 main handle 

positions).

- Overload protection: 

The electronic signal 

display (4) lights up and the load speed 

decreases slightly.

 The machine is overloaded. 

Work with a reduced load until the electronic 

signal display goes out.

- Overload protection: 

The electronic signal 

display (4) lights up and the load speed 

decreases dramatically.

 The motor temperature 

is too high! Run the machine in idling until it cools 

down and the electronic signal display switches 

off.

-

Metabo S-automatic safety stop: The 

electronic signal display (4) lights up and the 

machine SWITCHES OFF automatically.

 If the 

slew rate of the current is too high (for example, if 

the machine suddenly seizes or kickback occurs), 

the machine switches off. Switch off the machine 

at the trigger (6). Switch it on again and continue 

to work as normal. Try to prevent the machine 

from seizing. See section 4.2.

-

Restart protection: The electronic signal 

display (4) FLASHES and the machine does 

not start. 

The restart protection is active. If the 

mains plug is inserted with the machine switched 

on, or if the current supply is restored following an 

interruption, the machine does not start up. Switch 

the machine off and on again.

-

When switched on, the machine accelerates 

to maximum speed very quickly,

 i.e. automatic 

restriction of the starting current does not work 

(soft start). An electronic error exists. Other 

safety-related electronic functions are no longer 

available. Have the machine repaired immediately 

(see 16.).

Use only genuine Metabo accessories.
If you need any accessories, check with your 

dealer.

Metabo diamond cut-off wheels:

diameter 230 mm, laser-welded, suitable for dry 

cutting, wheel thickness in the clamping range = 

1.8 mm, bore = 22.23 mm, for wall chaser MFE 65
Application

Order no.

for hard and medium-hard 

materials (e.g. concrete, 

including reinforced concrete)

6.28134

for abrasive materials

(e.g. abrasive concrete, sandstone,

lime sand brick, aerated concrete 

and similar materials)

6.28145

Repairs to electrical tools must be carried out 

by qualified electricians ONLY! 

If you have Metabo electrical tools that require 

repairs, please contact your Metabo service centre. 

For addresses see www.metabo.com.
You can download spare parts lists from 

www.metabo.com.

The sanding dust generated may contain 

hazardous materials: do not dispose of with the 

household waste, but at a special collection point 

for hazardous waste.
Observe national regulations on environmentally 

compatible disposal and on the recycling of disused 

machines, packaging and accessories.

Only for EU countries: Never dispose of 

power tools in your household waste! In 

accordance with European Guideline 2002/

96/EC on used electronic and electric equipment 

and its implementation in national legal systems, 

used power tools must be collected separately and 

handed in for environmentally compatible recycling.

Explanation of details on page 3. Subject to 

changes serving technical progress.

D 

= Diameter of the diamond cut-off wheels

B

= Groove width options

T

= Adjustable depth of cut

P1

= Nominal power input

P2

= Power output

n = No-load 

speed

m

= Weight without mains cable

Vibration total value (vector sum of three directions) 

determined in accordance with EN 60745:

a

h

= Vibration emission level

K

h

  = Uncertainty (vibration)

The vibration emission level given in this 

information sheet has been measured in 

accordance with a standardised test given in EN 

60745 and may be used to compare one tool with 

another. It is also suitable for a provisional estimate 

of the vibratory load.
The specified vibration level applies to the main 

applications of the power tool. However, if the tool is 

used for other applications, with different 

accessories or when poorly maintained, the 

vibration level may vary. An estimation of the level of 

exposure to vibration should also take into account 

13. Cleaning

14. Troubleshooting

15. Accessories

16. Repairs

17. Environmental Protection

18. Technical Specifications