VERTO 51G075 - Инструкция по эксплуатации - Страница 11

11

GWARANCJA I SERWIS

Warunki gwarancji oraz opis postepowania w przypadku reklamacji 
zawarte są w załączonej Karcie Gwarancyjnej.

Serwis Centralny
GTX Service 

tel. +48 

22

 5

73

 0

3

 85

Ul. Pograniczna 

2

/4 fax. 

+48 

22

 5

73

 0

3

 8

3

0

2

-

2

85 Warszawa 

e-mail service@gtxservice.pl

Sieć Punktów Serwisowych do napraw gwarancyjnych 
i pogwarancyjnych dostępna na platformie internetowej 

gtxservice.pl

Grupa Topex zapewnia dostępność części zamiennych oraz materiałów 
eksploatacyjnych dla urządzeń i elektronarzędzi.

Pełna oferta części i usług na 

gtxservice.pl

. Zeskanuj kod QR i wejdź:

TRANSLATION OF THE ORIGINAL INSTRUCTION

ANGL

E

 G

R

IND

ER

51G075

NOTE: BEFORE THE POWER TOOL IS USED FOR THE FIRST TIME, READ 
THIS INSTRUCTION MANUAL AND KEEP IT FOR FUTURE REFERENCE.

DETAILED SAFETY REGULATIONS

ANGL

E

 G

R

IND

ER

, 

S

AF

E

TY WA

R

NING

S

S

afety guidelines for grinding, sanding with sandpaper, working 

with wire brushes and cutting using the grinding wheel.

• This power tool can be used as a regular grinder, sander 

for sanding with sandpaper, grinder for grinding with wire 
brushes and for cutting with a cut-off wheel. Observe all safety 
guidelines, instructions, descriptions and data provided with 
the power tool. 

Failure to observe the following recommendations 

may cause danger of electric shock, fire and/or serious injuries.

• This power tool cannot be used for polishing. 

When the power 

tool is used for other works than it is designed for, it may contribute to 
hazards and injuries.

• Do not use equipment, which is not designed and recommended 

by the manufacturer specifically for this device. 

The fact that it 

can be fastened to the power tool, does not guarantee safe operation.

• The permissible rotational speed of a working tool used cannot 

be lower than the maximum rotational speed given on the 
power tool. 

A working tool rotating faster than the permissible speed 

may break and its parts may chip off.

• The outside diameter and thickness of a working tool must 

correspond to dimensions of the power tool. 

A working tool of 

incorrect dimensions may not provide sufficient control and covering 
of the power tool.

• Working tools with threaded inserts must perfectly fit the 

thread in the spindle. In case of working tools that are fastened 
using a flange, the hole diameter of a working tool must fit the 
flange diameter. 

Working tools, which cannot be precisely seated in 

the power tool, rotate unevenly, vibrate heavily and may result in loss 
of control over the power tool.

• Under no circumstances, should damaged working tools be 

used. Before the power tool is used, accessories such as cut-off 
wheels should be checked for chips and cracks, grinding wheels 
should be checked for cracks, abrasion or heavy wear, while 
wire brushes for loose or broken wires. When the power tool 
or a working tool is dropped, it must be checked for damage 
or another, undamaged tool should be used. If a working tool 
is checked and fastened, the power tool should be switched on 
for a minute at the highest speed, paying attention so that the 
operator and bystanders are beyond the zone of the rotating 
tool.

 Damaged working tools often break in this test period.

• Always wear personal protective equipment. Depending on a 

type of work, a full face mask, eye protection or safety glasses 
should be worn. A dust mask, ear protection, protective gloves 
or a special apron protecting against small particles of abrasive 
material and workpiece should be worn, if needed. 

Protect your 

eyes against airborne foreign bodies occurring during operation. A 
dust mask and protective mask for the respiratory system must filter 
dust occurring during work. The influence of noise for a longer period 
of time may lead to deterioration of the hearing.

• Always make sure bystanders are in a safe distance from the 

power tool reach zone. All people staying in the vicinity of the 
operating power tool must use personal protective equipment. 

Chips of a workpiece or broken working tools may chip off and cause 
injuries also beyond the direct reach zone.

• When works are performed, during which the power tool may 

encounter hidden electric conductors or own power cord, 
the power tool should be held by the isolated surfaces of the 

GB