Sparky EX 150E - Инструкция по эксплуатации - Страница 7

5

Original instructions

EN

5. SERVICE

a) Have your power tool serviced by a qualified 

repair person using only identical replace-

ment parts. 

This will ensure that the safety of the 

power tool is maintained.

IV -  Random orbit sander  

safety warnings

During operation provide eye protection to 

prevent  eyes  from  exposure  to  flying  par

-

ticles. 

Wear goggles.

Wear hearing protection during continuous 

operation. 

Exposure to noise can cause hear-

ing loss.

  Take protective measures against inhala-

tion of dust. Some materials can contain 

toxic ingredients. 

Wear a dust mask and work 

with dust/chip extraction when connectable.

▪

Do not process materials containing asbestos. Asbes-

tos is considered carcinogenic.

▪

Use of protective gloves is recommended.

WARNING: 

Before connecting a tool to a 

power source be sure that the voltage supply is the 

same as that specified on the nameplate of the tool.

▪

A power source with a voltage greater than that speci-

fied for the tool can result in serious injury to the user, 

as well as damage to the tool.

▪

If in doubt, do not plug in the tool.

▪

Using a power source with a voltage less than the 

nameplate rating is harmful to the motor.

▪ Fully unwind cable drum extensions to avoid potential 

overheating.

▪

When an extension cable is required, you must en-

sure that it has the right ampere rating for your power 

tool and it is in safe electrical condition.

WARNING:

 Always switch off and unplug the 

power tool prior to any adjustment, servicing or main-

tenance or in case of mains drop-out.

▪

Use the power tool for dry sanding only.

▪

Use clamps or a vice to secure your work whenever 

possible.

▪

Use perforated hook-and-loop sandpaper with the 

prescribed dimensions.

▪

A sanding sheet that has been used for metal should 

not be used for other materials.

▪

Never switch on the orbital sander under load and 

leave it down only after final arrest.

▪

Do not overload the machine: operate with moderate 

pressure. Overloading occurs when you apply exces-

sive pressure, resulting in decrease of motor speed, 

which may cause inefficient operation and possible 

fault of the motor.

▪

Keep work area clean. Blends of materials are par-

ticularly dangerous. Dust from light alloys can burn or 

explode.

▪

The presence of harmful toxic dust, separated during 

processing materials containing lead, quartz (Silicium 

Dioxide), touching or inhaling it may be hazardous to 

the health of the operator or observers.

▪

Always keep the cord away from the working area of 

the power tool.

▪

Never use the machine with a damaged cable. Do 

not touch the damaged cable and pull the mains plug 

when the cable is damaged while operating. Dam-

aged cables increase the risk of electric shock.

▪

The tool must be used only for its prescribed purpose. 

Any use other than those mentioned in this Manual 

will be considered a case of misuse. The user and not 

the manufacturer shall be liable for any damage or in-

jury resulting from such cases of misuse.

▪

To use this tool properly, you must observe the safety 

regulations, the assembly instructions and the operat-

ing instructions found in this Manual. All persons who 

use and service the machine have to be acquainted 

with this Manual and must be informed about its po-

tential hazards. Children and frail people must not use 

this tool. Children should be supervised at all times if 

they are in the area in which the tool is being used. It 

is also imperative that you observe the accident pre-

vention regulations in force in your area. The same 

applies for general rules of occupational health and 

safety.

▪

The manufacturer shall not be liable for any changes 

made to the tool nor for any damage resulting from 

such changes.

▪

Power tools must not be used outdoors in rainy weath-

er, or in moist environment (after rain) or in close vicin-

ity with easily flammable liquids and gases. The work-

ing place should be well lit. 

V - Know your product

Before using the power tool, familiarize yourself with all 

the operating features and safety requirements.

Use the tool and accessories only for the applications 

intended. All other applications are expressly ruled out. 

  1.  Auxiliary handle fixing screw

  2.  Auxiliary handle

  3.  Electronic regulator of speed

  4.  ON/OFF switch 

  5.  Lock-on button

 6.  Handle

  7.  Power indicator

  8.  Dust collector bag

  9.  Dust extraction adapter

 10.  Dust extraction port

 11.   Abrasive sheet (sandpaper)

 12.   Sanding disc

 13.   Rubber seal

 14.    Screw

 15.    Guide

pages-EX 150E-2012.indd   5

19.11.2012 г.   10:05:34 ч.