Sparky EX 150E - Инструкция по эксплуатации - Страница 6

4

EX 150E • EX 150CE

EN

III -  General power tool 

safety warnings

WARNING!

Read all safety warnings and 

all instructions. 

Failure to follow the warnings and 

instructions  may  result  in  electric  shock,  fire  and/or 

serious injury. 

Save all warnings and instructions for future 

reference.

The term “power tool” in the warnings refers to your 

mains-operated (corded) power tool or battery-operated 

(cordless) power tool.

1. WORK AREA SAFETY

a) Keep work area clean and well lit. 

Cluttered or 

dark areas invite accidents.

b) Do not operate power tools in explosive at-

mospheres, such as in the presence of flam-

mable liquids, gases or dust. 

Power tools cre-

ate sparks which may ignite the dust or fumes.

c)  Keep children and bystanders away while op-

erating a power tool. 

Distractions can cause you 

to lose control.

2. ELECTRICAL SAFETY

a)  Power tool plugs must match the outlet. Nev-

er modify the plug in any way. Do not use any 

adapter plugs with earthed (grounded) power 

tools.

 Unmodified plugs and matching outlets will 

reduce risk of electric shock.

b)  Avoid body contact with earthed or grounded 

surfaces, such as pipes, radiators, ranges 

and refrigerators. 

There is an increased risk of 

electric shock if your body is earthed or grounded.

c)  Do not expose power tools to rain or wet con-

ditions. 

Water entering a power tool will increase 

the risk of electric shock.

d) Do not abuse the cord. Never use the cord 

for carrying, pulling or unplugging the power 

tool. Keep cord away from heat, oil, sharp 

edges or moving parts. 

Damaged or entangled 

cords increase the risk of electric shock.

e) When operating a power tool outdoors, use 

an extension cord suitable for outdoor use. 

Use of a cord suitable for outdoor use reduces the 

risk of electric shock.

f)  If operating a power tool in a damp location 

is unavoidable, use a residual current device 

(RCD) protected supply. 

Use of an RCD reduces 

the risk of electric shock.

3. PERSONAL SAFETY

a)  Stay alert, watch what you are doing and use 

common sense when operating a power tool. 

Do not use a power tool while you are tired or 

under the influence of drugs, alcohol or med-

ication. 

A moment of inattention while operating 

power tools may result in serious personal injury.

b) Use personal protective equipment. Always 

wear eye protection. 

Protective equipment such 

as dust mask, non-skid safety shoes, hard hat, or 

hearing protection used for appropriate conditions 

will reduce personal injuries.

c) Prevent unintentional starting. Ensure the 

switch is in the off-position before connect-

ing to power source and/or battery pack, 

picking up or carrying the tool. 

Carrying power 

tools with your finger on the switch or energising 

power tools that have the switch on invites acci-

dents.

d) Remove any adjusting key or wrench before 

turning the power tool on. 

A wrench or a key left 

attached to a rotating part of the power tool may 

result in personal injury.

e) Do not overreach. Keep proper footing and 

balance at all times. 

This enables better control 

of the power tool in unexpected situations.

f)  Dress properly. Do not wear loose clothing or 

jewellery. Keep your hair, clothing and gloves 

away from moving parts. 

Loose clothes, jewel-

lery or long hair can be caught in moving parts.

g) If devices are provided for the connection of 

dust extraction and collection facilities, ensure 

these are connected and properly used. 

Use of 

dust collection can reduce dust-related hazards.

4.  POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct 

power tool for your application. 

The correct 

power tool will do the job better and safer at the 

rate for which it was designed.

b) Do not use the power tool if the switch does 

not turn it on and off. 

Any power tool that can-

not be controlled with the switch is dangerous and 

must be repaired.

c) Disconnect the plug from the power source 

and/or the battery pack from the power tool be-

fore making any adjustments, changing acces-

sories, or storing power tools. 

Such preventive 

safety measures reduce the risk of starting the 

power tool accidentally.

d) Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with 

the power tool or these instructions to oper-

ate the power tool. 

Power tools are dangerous in 

the hands of untrained users.

e) Maintain power tools. Check for misalign-

ment or binding of moving parts, breakage of 

parts and any other condition that may affect 

the power tool’s operation. If damaged, have 

the power tool repaired before use. 

Many ac-

cidents are caused by poorly maintained power 

tools.

f)  Keep cutting tools sharp and clean. 

Properly 

maintained cutting tools with sharp cutting edges 

are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits 

etc. in accordance with these instructions, 

taking into account the working conditions 

and the work to be performed. 

Use of the pow-

er tool for operations different from those intended 

could result in a hazardous situation.

pages-EX 150E-2012.indd   4

19.11.2012 г.   10:05:33 ч.