Ryobi R18RT-0 (5133004366) - Инструкция по эксплуатации - Страница 3

1

 English 

|

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

UK

TR

EL

Safety, performance, and dependability have been given 
top priority in the design of your rotary tool.

INTENDED USE

The rotary tool is intended to be used only by adults who 
have read and understood the instructions and warnings in 
this manual, and can be considered responsible for their 
actions.
With appropriate accessories 

fi

 tted, the product is designed 

to perform cutting, grinding, sanding, sculpting, polishing, 
buf

fi

 ng, etching, engraving and drilling.

The product is intended for consumer use only.
Do not use the product for any other purpose. Use of the 
product for operations different from intended could result 
in a hazardous situation.

 WARNING

Read all safety warnings, instructions, illustrations 
and specifications provided with this power tool.

Failure to follow all instructions listed below may result in 
electric shock, 

fi

 re and/or serious injury.

Save all warnings and instructions for future reference.

ROTARY TOOL SAFETY WARNINGS

Safety warnings common for grinding, sanding, wire 
brushing, polishing, carving or abrasive cutting-off 
operations

■

This power tool is intended to function as a grinder, 
sander, wire brush, polisher, carving or cut-off tool. 
Read all safety warnings, instructions, illustrations 
and specifications provided with this power tool.

Failure to follow all instructions listed below may result 
in electric shock, fire and/or serious injury.

■

Do not use accessories which are not specifically 
designed and recommended by the tool 
manufacturer.

 Just because the accessory can be 

attached to your power tool, it does not assure safe 
operation.

■

The rated speed of the grinding accessories must 
be at least equal to the maximum speed marked on 
the power tool. 

Grinding accessories running faster 

than their rated speed can break and fly apart.

■

The outside diameter and the thickness of your 
accessory must be within the capacity rating of 
your power tool. 

Incorrectly sized accessories cannot 

be adequately controlled.

■

The arbour size of wheels, sanding drums or any 
other accessory must properly fit the spindle or 
collet of the power tool.

 Accessories that do not 

match the mounting hardware of the power tool will run 
out of balance, vibrate excessively and may cause loss 
of control.

■

Mandrel mounted wheels, sanding drums, cutters 
or other accessories must be fully inserted into 
the collet or chuck. 

If the mandrel is insufficiently 

held and/or the overhang of the wheel is too long, the 
mounted wheel may become loose and be ejected at 
high velocity.

■

Do not use a damaged accessory. Before each use 
inspect the accessory such as abrasive wheels for 
chips and cracks, sanding drum for cracks, tear or 
excess wear, wire brush for loose or cracked wires. 
If power tool or accessory is dropped, inspect for 
damage or install an undamaged accessory. After 
inspecting and installing an accessory, position 
yourself and bystanders away from the plane of 
the rotating accessory and run the power tool at 
maximum no-load speed for one minute. 

Damaged 

accessories will normally break apart during this test 
time.

■

Wear personal protective equipment. Depending 
on application, use face shield, safety goggles or 
safety glasses. As appropriate wear dust mask, 
hearing protectors, gloves and workshop apron 
capable of stopping small abrasive or workpiece 
fragments. 

The eye protection must be capable of 

stopping flying debris generated by various operations. 
The dust mask or respirator must be capable of filtrating 
particles generated by your operation. Prolonged 
exposure to high intensity noise may cause hearing 
loss.

■

Keep bystanders a safe distance away from work 
area. Anyone entering the work area must wear 
personal protective equipment. 

Fragments of 

workpiece or of a broken accessory may fly away and 
cause injury beyond immediate area of operation.

■

Hold power tool by insulated gripping surfaces 
only, when performing an operation where the 
cutting accessory may contact hidden wiring. 

Cutting accessory contacting a “live” wire may make 
exposed metal parts of the power tool “live” and could 
give the operator an electric shock.

■

Always hold the tool firmly in your hand(s) during 
the start-up.

 The reaction torque of the motor, as it 

accelerates to full speed, can cause the tool to twist.

■

Use clamps to support workpiece whenever 
practical.

Never hold a small workpiece in one hand 

and the tool in the other hand while in use.

 Clamping 

a small workpiece allows you to use your hand(s) to 
control the tool. Round material such as dowel rods, 
pipes or tubing have a tendency to roll while being cut, 
and may cause the bit to bind or jump toward you.

■

Position the cord clear of the spinning accessory. 

If you lose control, the cord may be cut or snagged 
and your hand or arm may be pulled into the spinning 
accessory.

■

Never lay the power tool down until the accessory 
has come to a complete stop.

 The spinning accessory 

may grab the surface and pull the power tool out of your 
control.

■

After changing the bits or making any adjustments, 
make sure the collet nut, chuck or any other 
adjustment devices are securely tightened. 

Loose 

adjustment devices can unexpectedly shift, causing 
loss of control, loose rotating components will be 
violently thrown.

■

Do not run the power tool while carrying it at your 
side.

 Accidental contact with the spinning accessory 

could snag your clothing, pulling the accessory into 
your body.