Metabo W 650-125 - Инструкция по эксплуатации - Страница 5

5

4

D

max

= 100 mm (4“) 630346000

D

max

= 125 mm (5“) 630352000

A

CLICK

630327000

B

(8)

(9)

(1)

(7)

C

(M 14) 630706000
(M 10) 34110205

ENGLISH en

Original instructions

The angle grinders, when fitted with original Metabo 

accessories, are suitable for grinding, sanding, 

separating and wire brushing metal, concrete, 

stone and similar materials without the use of water. 

The user bears sole responsibility for any damage 

caused by inappropriate use.

Generally accepted accident prevention 

regulations and the enclosed safety information 

must be observed.

For your own protection and for the 

protection of your power tool, pay 

attention to all parts of the text that are 

marked with this symbol!

WARNING – Read the operating 

instructions to reduce the risk of injury.

WARNING Read all safety warnings and 

instructions.

Failure to follow all safety 

warnings and instructions may result in electric 

shock, fire and/or serious injury.

Keep all safety instructions and information for 

future reference.

Always include these documents when passing on 

your power tool.

3.1 General Safety Recommendations for 

Grinding, Sanding, Wire Brushing or 

Abrasive Cutting:

Use

a) This power tool is intended to function as a

grinder, sander, wire brush or cut-off tool. Read

all safety warnings, instructions, illustrations

and specifications provided with this power 

tool. Failure to follow all instructions listed below 

may result in electric shock, fire and/or serious 

injury.

b) Operations such as polishing are not

recommended to be performed with this power

tool. Operations for which the power tool was not 

designed may create a hazard and cause personal 

injury.

c) Do not use accessories which are not

specifically designed and recommended by the

tool manufacturer. Even if an accessory can be

attached to your power tool, this does not ensure 

safe operation.

d) The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

e) The external diameter and thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories 

cannot be adequately guarded or controlled.

f) The threaded mounting of accessories must

match the grinder spindle thread. For 

accessories mounted by flanges, the arbour

hole of the accessory must fit the locating

diameter of the flange. Accessories that do not 

match the mounting hardware of the power tool will

run out of balance, vibrate excessively and may 

result in a loss of control.

g) Do not use damaged accessories. Inspect

accessories such as grinding discs before

each use for chips and cracks and inspect 

backing pads for cracks, tear or excess wear

and wire brushes for loose or cracked wires. If

a power tool or accessory is dropped, inspect 

for damage or install an undamaged 

accessory. After inspecting and installing an

accessory, position yourself and bystanders 

away from the plane of the rotating accessory 

and run the power tool at the maximum no-load 

speed for one minute. Damaged accessories will

normally break apart during this test time.

h) Wear personal protective equipment. Use a

face shield, safety goggles or safety goggles 

depending on the application. If necessary, 

wear a dust mask, hearing protectors, gloves 

and a workshop apron capable of stopping

small abrasive or workpiece fragments. Eye 

protection must be capable of stopping flying debris 

generated by various operations. A dust mask or

respirator must be capable of filtering particles 

generated by your operation. Prolonged exposure 

to high intensity noise may cause hearing loss. 

i) Keep bystanders a safe distance away from

the work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of a workpiece or broken accessory may 

fly off and result in injury beyond the immediate area

of operation. 

j) Only hold the cordless tool by its insulated

grip areas while completing work where the 

tool may come into contact with hidden power 

lines or its own power cable. Cutting accessory 

contacting a "live" wire may make exposed metal 

parts of the power tool "live" and could give the 

operator an electric shock.

k) Position the cord clear of the rotating

accessory. If you lose control, the cord may be cut 

or snagged and your hand or arm may be pulled into

the rotating accessory.

I) Never lay the power tool down until the

accessory has come to a complete stop. The 

rotating accessory may grab the surface and pull 

the power tool out of your control.

m) Do not run the power tool while carrying it at

your side. Accidental contact with a rotating

accessory could snag your clothing, pulling the 

accessory into your body. 

n) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside the housing 

1. Specified Conditions of Use

2. General Safety Information

3. Special Safety Instructions